hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.7.4.2 Procedure | a) The SS activates the carriers and monitors for RA requests from the MS on carriers 1, 2, and 4.
b) The MS is switched on.
c) The MS is switched off. The SS deactivates the carriers.
d) The MS is placed in cell test operation mode.
NOTE: Cell test mode is a mode of operation defined in SIM administrative data field.
e) The SS activates the carriers and monitors for RA requests from the MS on carriers 1, 2, and 3.
f) The MS is switched on. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.7.5 Test requirements | 1) After step b), the first response from the MS shall be on carrier 4 within 33 s, followed by a response on carrier 1 before a response (if any) on carrier 2 within 50 s.
2) After step f), the first response from the MS shall be on carrier 3 within 33 s, followed by a response on carrier 1 before a response (if any) on carrier 2 within 50 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.8 R-GSM or ER-GSM cell reselection when C1 (serving cell) < 0 for 5 s | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.8.1 Definition | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.8.2 Conformance requirement | 1. At least every 5 s the MS shall calculate the value of C1 and C2 for the serving cell and recalculate C1 and C2 values for non serving cells (if necessary). The MS shall then check whether:
i) The path loss criterion (C1) for current serving cell falls below zero for a period of 5 s. This indicates that the path loss to the cell has become too high. 3GPP TS 05.08, subclause 6.6.2.
2. While camped on a cell of the selected PLMN ("camped normally"), the MS may need to select a different cell ("normal cell reselection" state). The following events trigger a cell reselection:
(i) The path loss criterion parameter C1 (see subclause 3.6) indicates that the path loss to the cell has become too high.; 3GPP TS 03.22, subclause 4.5. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.8.3 Test purpose | 1. To verify that the MS meets conformance requirement 1.
2. To verify that the MS meets conformance requirement 2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.8.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.8.4.1 Initial conditions | Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
63 / -50
33 / -80
OFF
OFF
OFF
OFF
RXLEV_ACCESS_MIN (dBV emf() / dBm)
43 / -70
23 / -90
CRO
30 dB
TO
0
PT
0
C1
20
10
C2
50
10
NOTE: With BS_PA_MFRMS = 5 (default value), the averaging time of the MS on the serving cell BCCH is 5,9 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.8.4.2 Procedure | a) The SS activates the carriers. The MS is not paged on carrier 1. The SS monitors carriers 1 and 2 for RA requests from the MS.
b) The MS is switched on.
c) The SS reduces signal level on carrier 1 to ‑80 dBm / 33 dBV emf() for 4 s. Then, the SS raises the level back to -50 dBm / 63 dBV emf(). (C1 becomes ‑10 dB and C2, 20 dB during this period).
d) The SS reduces signal level on carrier 1 to -80 dBm / 33 dBV emf(). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.8.5 Test requirements | 1) After step b), there shall be no access on carrier 1 or carrier 2, within 50 s.
2) After step c), there shall be no access on carrier 2 within 30 s.
3) After step d), the MS shall access on carrier 2 within 20 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.9 R-GSM or ER-GSM running average of the surrounding cell BCCH carrier signal levels | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.9.1 Definition | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.9.2 Conformance requirement | 1. Whilst in idle mode an MS shall continue to monitor all BCCH carriers as indicated by the BCCH allocation (BA - See table 1). A running average of received level in the preceding 5 to:
- Max. {5, ((5 N + 6) DIV 7) BS_PA_MFRMS / 4}
- seconds shall be maintained for each carrier in the BCCH allocation. N is the number of non-serving cell BCCH carriers in BA and the parameter BS_PA_MFRMS is defined in 3GPP TS 05.02; 3GPP TS 05.08, subclause 6.6.1.
2. The same number of measurement samples shall be taken for all non-serving cell BCCH carriers of the BA list, and the samples allocated to each carrier shall as far as possible be uniformly distributed over each evaluation period.; 3GPP TS 05.08, subclause 6.6.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.9.3 Test purpose | 1. To verify that if the MS calculates a received level average (over 5 s) for a non-serving suitable cell which results in the value of C2 exceeding the value of C2 for the serving cell, then cell reselection takes place to the non-serving cell.
2. To verify that by using suitable varying levels of signal strength for non serving cells, the MS samples on non serving cell BCCH carriers are as far as possible distributed uniformly over each evaluation period. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.9.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.9.4.1 Initial conditions | Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
53 / -60
33 / -80
OFF
OFF
OFF
OFF
RXLEV_ACCESS_MIN
(dBV emf() / dBm)
23 / -90
23 / -90
C1
30
10
C2
30
10
BS_PA_MFRMS is set to 4 for this test.
The BA(BCCH) list only contains 7 ARFCNs including the ARFCNs of the carriers used during the test.
Note: If the MS supports the ER-GSM Band, the SI2bis (using the ER-GSM) should be used.
NOTE: With 7 ARFCNs in the BA(BCCH) list and BS_PA_MFRMS=4 the MS will maintain a running average on surrounding cells over a period of 5 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.9.4.2 Procedure | a) The SS activates the carriers. The MS is not paged on carrier 1. The SS monitors carriers 1 and 2.
b) The MS is switched on.
c) The SS starts switching the level of carrier 2 between -80 dBm and -57 dBm every 2,7 s and continues to do so until the end of the test.
d) The SS decreases the level of carrier 1 to -76 dBm.
NOTE: As a result of the switching in levels, the running average on carrier 2 will be between -66dBm and ‑71dBm, assuming that samples are distributed over five consecutive paging blocks. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.9.5 Test requirements | 1) After step b), there shall be no access from the MS on carrier 1 or carrier 2, within 50 s.
2) After step c), there shall be no access from the MS on carrier 1 or 2 within 25 s.
NOTE: Any potential access on is likely to occur within 20 s.
3) After step d), the MS shall access on carrier 2 within 20 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.10 R-GSM or ER-GSM running average of the serving cell BCCH carrier signal level | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.10.1 Definition | The MS is required to monitor continuously the BCCH carrier signal level of the serving cell (and to compare it to the BCCH carrier signal levels of the non-serving cells) to guarantee that it is camped on the most suitable cell. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.10.2 Conformance requirement | 1. For the serving cell, receive level measurement samples shall be taken at least for each paging block of the MS. The receive level average shall be a running average determined using samples collected over a period of 5 s or five consecutive paging blocks of that MS, whichever is the greater period. New receiving level average values shall be calculated as often as possible. 3GPP TS 05.08, suclause 6.6.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.10.3 Test purpose | 1. To verify that by using suitable varying levels of signal strength for the serving cell, the MS performs a running average over 5 consecutive paging blocks. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.10.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.10.4.1 Initial conditions | Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF signal level
(dBV emf() / dBm)
63 / -50
39 / -74
OFF
OFF
OFF
OFF
RxLev_Access_Min
(dBV emf() / dBm)
23 / -90
23 / -90
C1
40
16
C2
40
16
NOTE: With BS_PA_MFRMS = 5 (default value), the averaging time of the MS on the serving cell BCCH is 5,9 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.10.4.2 Procedure | a) The SS activates the carriers. The MS is not paged on carrier 1. The SS monitors carriers 1 and 2 for RA requests from the MS.
b) The MS is switched on.
c) After 50 s the SS starts switching the level of carrier 1 between ‑80 dBm and ‑50 dBm every 3 s.
NOTE: As a result of the switching in levels, the running average on carrier 1 will be between ‑62 dBm and ‑68 dBm over five consecutive paging blocks.
d) The SS increases the level of carrier 2 to ‑56 dBm. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.10.5 Test requirement | 1) After step c), the MS shall not access on carrier 2, within 25 s.
2) After step d), the MS shall access on carrier 2, within 30 s.
NOTE: 13,75 s to perform running average, 10 s to detect C2 differences, 2,4 s to read BCCH of carrier 2, 1 s to perform RA. Total 27,15 s, allow 30 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.11 R-GSM or ER-GSM Updating the list of six strongest neighbour carriers and decoding the BCCH information of a new carrier on the list | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.11.1 Definition | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.11.2 Conformance requirement | 1. The list of the 6 strongest non-serving carriers shall be updated at least as often as the duration of the running average defined for measurements on the BCCH allocation and may be updated more frequently; 3GPP TS 05.08, subclause 6.6.1.
2. When the MS recognizes that a new BCCH carrier has become one of the 6 strongest, the BCCH data shall be decoded for the new carrier within 30 s; 3GPP TS 05.08, subclause 6.6.1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.11.3 Test purpose | 1. To verify that MS meets conformance requirement 1.
2. To verify that MS meets conformance requirement 2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.11.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.11.4.1 Initial conditions | Six BCCH carriers are established with the system information contents of table 20.21.1.
Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
Carrier 7
RF signal level
(dBV emf ( )/dBm)
53 / -60
48 / -65
43 / -70
38 / -75
33 / -80
33 / -80
38 / -75
RXLEV_ACCESS_MIN
-90
-90
-90
-90
-90
-90
-110
C1
30
25
20
15
10
10
35
C2
30
25
20
15
10
10
35
The BA(BCCH) list contains only eight ARFCNs and includes those of carriers 1 to 7.
Note: If the MS supports the ER-GSM Band, the SI2bis (using the ER-GSM) should be used.
BS_PA_MFRMS is set to 3 during this test.
NOTE: The combination of 8 carriers on the BA list and BS_PA_MFRMS = 3 leads to averaging time of 5 s. Hence 5 s is also the updating time of the list of six strongest neighbour carriers. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.11.4.2 Procedure | a) The SS activates carriers 1 to 6. The MS is not paged on any of the carriers.
b) The MS is switched on.
c) After 60 s, the SS activates carrier 7 and pages the MS continuously on this carrier. The SS monitors carrier 7 for RA requests from the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.11.5 Test requirements | 1) The MS shall access on carrier 7 within 55 s of activating carrier 7.
NOTE: 5,5 s to notice new strongest carrier in top 6 (because the updating time for six strongest is 5 s (+10 %)), 33 s to read BCCH, 15 s for reselection, since the MS has already performed the running average on the new strongest carrier, allow 55 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.12 R-GSM or ER-GSM decoding the BCCH information of the neighbour carriers on the list of six strongest neighbour carriers | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.12.1 Definition | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.12.2 Conformance requirement | 1. The MS shall attempt to decode the BCCH data block that contains the parameters affecting cell reselection for each of the 6 strongest non‑serving cell BCCH carriers at least every 5 minutes; 3GPP TS 05.08, subclause 6.6.1.
NOTE: Verification of cell reselection as implicitly tested here is performed in subclause 20.21.3. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.12.3 Test purpose | 1. To verify that the MS decodes the BCCH data block that contains the parameters affecting cell reselection for a non‑serving cell BCCH carrier, (which is in the list of six strongest neighbour cells), at least every 5 minutes. This is achieved by changing the BCCH data such that the value of C2 for the non serving cell exceeds the value of C2 for the serving cell, and observing that the MS performs cell reselection within 5 minutes plus the time allowed for cell reselection after the change of the BCCH data. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.12.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.12.4.1 Initial conditions | Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF signal level
(dBV emf() / dBm)
38 / -75
33 / -80
OFF
OFF
OFF
OFF
C1
15
10
C2
15
10 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.12.4.2 Procedure | a) The SS activates the carriers. The MS is not paged on carrier 1. The SS monitors carriers 1 and 2.
b) The MS is switched on.
c) The SS changes the RXLEV_ACCESS_MIN in the BCCH data of carrier 2 to be -100 dBm.
NOTE: With the above change the C2 of carrier 2 becomes 20 whereas the C2 of carrier 1 stays at 15. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.12.5 Test requirements | 1) After step b), there shall be no access from the MS on carrier 1 or carrier 2 within 50 s.
2) After step c), the MS shall access on carrier 2 within 345 s of the change in the BCCH data of carrier 2.
NOTE: 330 s for decode of BCCH of carrier 2 (300 s +10 %), 15 s for reselection of carrier 2, since the MS already has a running average on carrier 2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.13 R-GSM or ER-GSM decoding the BSIC of the neighbour carriers on the list of six strongest neighbour carriers | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.13.1 Definition | Void. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.13.2 Conformance requirement | 1. The MS shall attempt to check the BSIC for each of the 6 strongest non-serving cell BCCH carriers at least every 30 s, to confirm that it is monitoring the same cell. If a change of BSIC is detected then the carrier shall be treated as a new carrier and the BCCH data redetermined; 3GPP TS 05.08, subclause 6.6.1.
NOTE: Verification of cell reselection as implicitly tested here is performed in subclause 20.21.3. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.13.3 Test purpose | 1. To verify that the MS will check the BSIC of the non-serving cell, which is in the list of six strongest neighbour cells, by changing the BSIC and the BCCH data of the non-serving cell such that the value of C2 for that cell exceeds the value of C2 of the serving cell, and observing that the MS performs cell reselection within the time allowed to check the BSIC, redetermine the BCCH data and perform cell reselection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.13.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.13.4.1 Initial conditions | Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF signal level
(dBV emf() / dBm)
38 / -75
33 / -80
OFF
OFF
OFF
OFF
C1
15
10
C2
15
10 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.13.4.2 Procedure | a) The SS activates the carriers. The MS is not paged on carrier 1. The SS monitors carriers 1 and 2.
b) The MS is switched on.
c) The SS changes the BSIC of carrier 2 by changing the Base Station Colour Code (BCC) part of the BSIC. The SS also changes the RXLEV_ACCESS_MIN in the BCCH data of carrier 2 to be -100 dBm.
NOTE: With the above change to the BCCH data the C2 of carrier 2 becomes 20 whereas the C2 of carrier 1 stays at 15. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.13.5 Test requirements | 1) In step b), there shall be no access from the MS on carrier 1 or carrier 2 within 50 s.
2) After step c), the MS shall access on carrier 2 within 85 s of the change in the BSIC value (and BCCH data) of carrier 2.
NOTE: 33 s for check of BSIC on carrier 2, 33 s for decode of BCCH of carrier 2, 15 s for reselection of carrier 2, since the MS already has a running average on carrier 2, allow 85 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.14 R-GSM or ER-GSM emergency calls | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.14.1 Definition | - |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.14.2 Conformance requirement | 1. When in a limited service state, the MS shall be able to initiate emergency calls; 3GPP TS 05.08, subclause 6.8.
2. When in a limited service state and if not camped on a cell, the MS shall monitor the signal strength of all 194 RF channels, and search for a BCCH carrier which has C1>0 and which is not barred. When such a carrier is found, the MS shall camp on that cell, irrespective of the PLMN identity; 3GPP TS 05.08, subclause 6.8.
3. The MS shall perform cell reselection at least among the cells of the PLMN of the cell on which the MS has camped, according to the algorithm of 3GPP TS 03.22, subclauses 4.5 and 3.7, except that a zero value of CELL_RESELECT_HYSTERESIS shall be used; 3GPP TS 05.08, subclause 6.8. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.14.3 Test purpose | 1. To verify that the MS shall be able to initiate emergency calls when no suitable cells of the selected PLMN are available, but at least one acceptable cell is available.
2. To verify that the MS selects a cell with C1 > 0 and CBA = 0 when no suitable cells of the selected PLMN are available.
3. To verify that the MS, when performing cell reselection in the limited service state, uses CELL_RESELECT_HYSTERESIS = 0. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.14.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.14.4.1 Initial conditions | Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF signal level
(dBV emf() / dBm)
38 / -75
33 / -80
33 / -80
OFF
OFF
OFF
RXLEV_ACCESS_MIN
(dBV emf() / dBm)
23 / -90
43 / -70
23 / -90
CELL_BAR_ACCESS
1 (barred)
0
0
MCC,MNC
forbidden
forbidden
forbidden
CELL_RESELECT_HYST
0
0
14 dB
C1
15
-10
10
NOTE: All the BCCH carriers belong to the same PLMN, which is not the MS's home PLMN and is in the SIM's forbidden PLMN's list. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.14.4.2 Procedure | a) The SS activates the carriers. The SS monitors for RA attempts from the MS on carriers 1, 2 and 3 for the duration of the test.
b) The MS is switched on.
c) 50 s after switch on, an emergency call is initiated on the MS.
d) The SS changes the CBA of carrier 1 to 0.
NOTE 1: The MS should reselect to carrier 1 because it should not take into account the CELL_RESELECT_HYST value of 14 but use 0 instead.
e) After 345 s an emergency call is initiated on the MS.
NOTE 2: 330 s to detect change of BCCH data, 15 s to perform reselection of carrier 1, since the MS already has a running average on carrier 1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.14.5 Test requirements | 1) In step c), the first access by the MS shall be on carrier 3.
2) In step e), the first access from the MS shall be on carrier 1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.15 R-GSM or ER-GSM cell reselection due to MS rejection "LA not allowed" | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.15.1 Definition | While camped on a cell of the selected PLMN the MS may need to select a different cell in order to fulfil the normal service state. This ensures that the MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
This process goes on while camping on a cell which pertains to an LA which is placed in the list of "forbidden LAIs for regional provision of service". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.15.2 Conformance requirement | 1. In response to a registration attempt, when receiving an LU reject with cause value "LA not allowed", the MS stores this LAI in a list of "forbidden LAIs for regional provision of service", to prevent repeated attempts to access a cell of the forbidden LA, 3GPP TS 03.22, subclause 3.3.
2. If the MS has received the cause 'LA not allowed', it shall ignore this fact when selecting a cell to camp on, i.e. it shall not reject a cell for camping on because that cell is part of a LA where this cause has been received, 3GPP TS 03.22, subclause 3.5.4.
3. In response to a registration attempt, when receiving an LU reject with cause value "LA not allowed", the MS continues to perform normal cell-reselection, 3GPP TS 03.22, subclause 4.4.2
4. A new LU attempt shall only be performed when a new LA (or new PLMN) is entered according to the cell reselection procedure, 3GPP TS 03.22, subclause 3.3 and figure 4.
NOTE: LA stands for "Location Area" and LU stands for "Location Update". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.15.3 Test purpose | 1. To verify that if an LU is rejected with cause "LA not allowed" that the LAI of that cell is written into a forbidden list which prevents the MS from performing LU onto another cell in that LA. This is verified indirectly in test purposes 2, 3 and 4.
2. To verify that the MS will not reject a cell for camping on because that cell is part of a LA in the list of "forbidden LAIs for regional provision of service". This is verified indirectly by making the MS attempt an emergency call and checking that the channel request message is transmitted on the correct cell.
3. To verify that the MS when receiving an LU reject with cause value "LA not allowed", the MS continues to perform normal cell-reselection:
Cell reselection is triggered if there is a better cell (in terms of the path loss criterion C2) in the same LA, or a much better cell in another LA of the selected PLMN (using the CRH parameter). 3GPP TS 03.22, subclauses 3.4 and 4.5.
4. To verify that a new LU attempt will be performed when a new LA (or new PLMN) is entered, 3GPP TS 03.22, subclause 3.3 and figure 4. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.15.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.15.4.1 Initial conditions | Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
63 / -50
54 / -59
44 / -69
OFF
OFF
OFF
RXLEV_ACCESS_MIN
(dBV emf() / dBm)
53 / -60
35 / -78
29 / -84
CRH
14
0
10
LAC
H1111
H2222
H1111
ATT
1
1
1
C1
10
19
15
C2
10
19
15 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.15.4.2 Procedure | a) The SS activates the carriers. The SS monitors all RA requests from MS on carriers 1, 2 and 3 until step e) has been completed. Only idle-paging is sent on all channels.
b) The MS is switched on.
c) When the MS performs an IMSI attach onto carrier 1, the SS shall reject it with cause "LA not allowed".
d) 30 s after the MS has returned to idle mode (channel release after LU reject), the MS is manually commanded to set up an emergency call.
NOTE 1: C2 of carrier 3>C2 of carrier 1. Carriers 1 and 3 belong to the same LA.
e) The SS rejects the CM service request from the MS, with a CM service reject message with cause value #17 (Network Failure).
NOTE 2: Cause values #4 (IMSI unknown in VLR) or #6 (Illegal ME) lead to unwanted behaviour of the mobile.
f) 10 s after the MS has returned to idle mode (channel release after CM service reject), the SS increases the level of carrier 2 to 65 dBV emf().
NOTE 3: C2 of carrier 2 = 30, now larger than C2 of carrier 3 + CRH.
g) The SS shall accept any LU on carrier 2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.15.5 Test requirements | 1) After step b), the MS shall respond on carrier 1 within 33 s.
2) In step d), the MS shall access on carrier 3 with a channel request message, within 15 s of being commanded to set up the emergency call.
3) After increasing the level of carrier 2 in step f), the MS shall reselect and access onto carrier 2 requesting an LU within 30 s.
NOTE: 13,75 s to perform running average, 10 s to detect C2 differences, 2,4 s to read BCCH of carrier 2, 1 s to perform RA. Total 27,15 s, allow 30 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.16 R-GSM or ER-GSM downlink signalling failure | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.16.1 Definition | See conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.16.3 Test purpose | 1. To verify that the MS initializes the DSC counter in accordance with the conformance requirement. This is verified indirectly.
2. To verify that whenever the MS successfully decodes a message on paging subchannel, the DSC is increased by 1, (however never beyond the nearest integer to 90/N). This is verified indirectly.
3 To verify that whenever the MS can not successfully decode a message on paging subchannel, the DSC decreased by 4. This is verified indirectly.
4. To verify that when the DSC reaches 0, a downlink signalling failure shall be declared and the MS will perform cell reselection. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.16.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.16.4.1 Initial conditions | Two BCCH carriers are established with the system information contents of table 20.21.1.
Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF signal level
(dBV emf() / dBm)
43 / -70
33 / -80
OFF
OFF
OFF
OFF
C1 = C2
20
10
NOTE: The DSC counter will have a value 18 (90/5). |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.16.4.2 Procedure | a) The MS is switched on. On carrier 1 valid layer 3 messages shall be sent in the paging blocks, but not paging the MS (idle paging). On carrier 2 the MS is paged continuously in all paging blocks.
b) After 40 s the SS sends corrupted data (using random data, wrong parity bits see 3GPP TS 05.03, subclauses 4.3 and 4.1.2 or other lower layer error) in four successive paging blocks to carrier 1 and then reverts to sending normal data.
NOTE 1: Sending corrupted, i.e. non-decodable data on four successive paging blocks should decrease the DSC to 2.
c) The SS monitors all accesses on both carriers for 30 s.
d) The SS sends corrupted data in five successive paging blocks to carrier 1 and then reverts to sending normal data.
NOTE 2: Sending random, data on five successive paging blocks should decrease the DSC to < 0 and cause a cell reselection.
e) The SS monitors all accesses on both carriers for 30 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.16.5 Test requirements | 1) There shall be no access to carrier 2 in test steps a) and c).
2) The MS shall access on carrier 2 at test step e) within 15 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.17 R-GSM or ER-GSM cell selection if no suitable cell found in 10 s | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.17.1 Definition | See conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.17.2 Conformance requirement | If no suitable cell is found in cell reselection process within 10 s, the cell selection algorithm of 3GPP TS 03.22 shall be performed, 3GPP TS 05.08; subclause 6.6.2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.17.3 Test purpose | To verify that the MS fulfils the conformance requirement. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.17.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.17.4.1 Initial conditions | One BCCH carrier is established with the system information contents of table 20.21.1.
Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF signal level
(dBV emf() / dBm)
43 / -70
OFF
OFF
OFF
OFF
OFF
C1 = C2
20 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.17.4.2 Procedure | a) The MS is switched on. Idle paging is sent on carrier 1.
b) After the MS indicates service the SS reduces the transmit level of carrier 1 to 13 dBV emf() (so that C1 of carrier 1 becomes ‑10) and turns on a new carrier (carrier 2) at a level of 33 dBV emf(). Carrier 2 shall not be in the MS BA list (i.e. it shall not be one of the carriers that MS has been monitoring after camped on carrier 1).
c) The SS shall monitor all accesses on carriers 1 and 2 for 60 s.
NOTE: The access on carrier 2 should not take longer than 50 s. (5 s to rxlev averages, 5 s for C1 < 0 duration, 10 s for searching another suitable cell, 30 s for cell selection), 60 s is a safe time to wait. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.17.5 Test requirements | The MS shall access on carrier 2 at test step c) within 60 s. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.18 R-GSM or ER-GSM cell reselection due to MS rejection "Roaming not allowed in this LA" | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.18.1 Definition | While camped on a cell of the selected PLMN the MS may need to select a different cell in order to fulfil the normal service state. This ensures that the MS is camped on a cell from which it can reliably decode downlink data and with which it has a high probability of communications on the uplink.
The MS looks for suitable neighbour cells which satisfies 4 constraints including that It should not be in an LA which is in the list of "forbidden LAs for roaming". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.18.2 Conformance requirement | 1. To prevent repeated attempts to have roaming service on a not allowed LA, when the MS is informed that an LA is forbidden, the LA is added to a list of "forbidden LAs for roaming" which is stored in the MS, 3GPP TS 03.22, subclause 3.1.
2. If the MS has received the cause "Roaming not allowed in this LA", in response to a LU attempt, the Network Selection Procedure shall be started, 3GPP TS 03.22; subclause 4.3.3 L3, 3GPP TS 04.08 / 3GPP TS 24.008; subclause 4.4.4.7.
3. The MS can only perform camping on a suitable cell, which:
- should not be in an LA which is in the list of "forbidden LAs for roaming" 3GPP TS 03.22, subclause 3.2.1.
NOTE: LA stands for "Location Area" and LU stands for "Location Update". |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.18.3 Test purpose | 1. To verify that if an LU is rejected with cause "Roaming not allowed in this LA", that the LAI of that cell is written into a forbidden list which prevents the MS from camping onto any cell in that LA.
2. To verify that if the MS has received the cause "Roaming not allowed in this LA", in response to a LU attempt, the Network Selection Procedure is initiated. This is verified indirectly by test purpose 3, in that the new LA is accessed as part of cell selection, hence CRH is disregarded.
3. To verify that if an LU is rejected, when attempting LU in a LA with LAI = LAI1, with cause "Roaming not allowed in this LA" and only cells of the selected PLMN are available, the MS will only camp and attempt LU in any LA with LAI <> LAI1. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.18.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.18.4.1 Initial conditions | Parameters changed from Default values table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBV emf() / dBm)
63 / -50
53 / -60
OFF
OFF
OFF
OFF
RXLEV_ACCESS_MIN
(dBV emf() / dBm)
23 / -90
23 / -90
MNC
MNC <> HPLMN
MNC <> HPLMN
MCC
MCC of HPLMN
MCC of HPLMN
CRH
0
0
LAC
H1111
H2222
ATT
1
1
C1
40
30
C2
40
30 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.18.4.2 Procedure | a) The MS is switched on. Idle paging is sent on all carriers.
b) The SS monitors all RA requests from MS on carriers 1 and 2.
c) When the MS performs an IMSI attach onto carrier 1, the SS shall reject it with cause "Roaming not allowed in this LA".
d) The SS shall accept any LU on carrier 2.
e) The SS monitors all RA requests from MS on carriers 1 to 2. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.18.5 Test requirements | 1) The MS should respond on carrier 1 within 33 s of switch on.
2) After LU reject, the MS shall initiate the Network Selection Procedure and access onto Carrier 2 as part of cell selection within 33 s from returning to idle mode after the LU reject.
NOTE: The timing requirement in b) is given only for testing purposes only. No timing requirements are defined for the Network Selection Procedure, but the time allowed for cell selection (see 20.21.1) should be adequate.
3) After the LU reject on carrier 1, there shall be no more access attempts on this carrier. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.19 R-GSM or ER-GSM cell selection on release of SDCCH and TCH | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.19.1 Definition | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.19.2 Conformance requirement | 1. When the SS releases a TCH or SDCCH and returns to idle mode, it shall, as quickly as possible camp on the BCCH carrier of the cell whose channel has just been released. If the full BCCH data for that cell was not decoded in the preceding 30 s, the MS shall then attempt to decode the full BCCH data. Until the MS has decoded the BCCH data required for determining the paging group, it shall also monitor all paging blocks on timeslot 0 of the BCCH carrier for possible paging messages that might address it. If the MS receives a page before having decoded the full BCCH data for the cell, the MS shall store the page and respond once the full BCCH data has been decoded, provided that the cell is not barred and the MSs access class is allowed. 3GPP TS 05.08, subclause 6.7. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.19.3 Test purpose | 1. To verify that on release of a TCH or an SDCCH, the MS camps as quickly as possible on the BCCH carrier of the cell whose channel has just been released.
NOTE: This is implicitly tested by the MS responding to a paging request. The decoding of BCCH data cannot be explicitly tested. However, the MS shall monitor for paging messages which may address it if it decodes the BCCH. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.19.4 Method of test | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.19.4.1 Initial conditions | a) Parameters changed from default values in table 20.21.1.
Parameter
Carrier 1
Carrier 2
Carrier 3
Carrier 4
Carrier 5
Carrier 6
RF Signal Level
(dBmV emf() / dBm)
53 / -60
33 / -80
OFF
OFF
OFF
OFF
RXLEV_ACCESS_MIN
(dBmV emf() / dBm)
23 / -90
23 / -90
BS_PA_MFRMS
2
2
ATT
1
C1
30
10
C2
30
10
b) Carrier 1 is configured to have a combined control channel.
c) Carrier 2 is configured to have a non combined control channel. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.19.4.2 Test procedure | a) The SS activates the carriers. No paging messages are transmitted on carrier 1 or carrier 2.
b) The MS is switched on.
c) In response to the MS access for IMSI attach, the SS allocates a combined SDDCH/4, accepts the IMSI attach procedure and then releases the link. After 0,5 s but within 1 s of transmitting the UA frame on completion of the IMSI attach procedure, the SS transmits a single PAGING REQUEST in the appropriate paging block of the MS on carrier 1.
d) When the MS responds to paging, the SS establishes a call on a traffic channel.
e) The SS increases the level of carrier 2 to 63 dBmV emf().
f) After 10 s the SS performs a handover to another TCH, with the parameters of carrier 2 indicated in the CELL DESCRIPTION information element of the HANDOVER COMMAND message.
g) After a further 10 s, the SS clears down the call. After 0,5 s but within 1 second of transmitting the UA frame, the SS transmits a single PAGING REQUEST on carrier 2 in the appropriate paging block of the MS. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.21.19.5 Test requirements | 1) After step b) the MS shall access in order to commence an IMSI attach procedure on carrier 1 within 33 s.
2) In step c), the MS shall respond to paging within 3 seconds of transmitting the PAGING REQUEST.
3) In step g), the MS shall respond to paging within 3 seconds of transmitting the PAGING REQUEST. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22 GPRS Cell Selection and Reselection | The absolute accuracy of the MS signal level measurements is assumed to be ±6 dB. A difference of at least 8 dB is allowed for cases of discrimination between C1, C31, C32 values and 0.
The relative accuracy of the MS signal level measurements is assumed to be ±3 dB for the signal levels used in the tests of this subclause. A difference of at least 5 dB is allowed for cases of discrimination between C1 and C31 and C32 values on different carriers.
NOTE 1: The accuracy of MS signal level measurements is specified in 3GPP TS 05.08/45.008. For all of the tests in this subclause, the signal levels used are greater than 1 dB above reference sensitivity level.
NOTE 2: The tolerance on timers specified in 3GPP TS 05.08/45.008 is ±10 % except for PENALTY_TIME where it is ±2 s. In the tests of this subclause, the test requirements include these tolerances. Consequently, the times stated in the test requirement sometimes differ from the corresponding timer in the conformance requirement.
Where pulsed signals are specified, the SS tolerance on pulse width is ±2 % and the SS tolerance on power level ±1 dB.
The MS shall perform cell re-selection according to the idle mode procedures defined in clause 6 of 3GPP TS 05.08/45.008 and therefore tests defined in clause 20 of TS 51.010 apply.
The support of GPRS shall be indicated in SYSTEM INFORMATION TYPE 3 message. In addition, the support of GPRS shall be indicated in either SYSTEM INFORMATION TYPE 4 or SYSTEM INFORMATION TYPE 7 and 8 messages. If GPRS is supported, SYSTEM INFORMATION TYPE 13 message shall be sent. SI 13 message shall not be sent if GPRS is not supported (3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.2.2.1). Additional requirements for the broadcast of system information in a cell supporting GPRS are specified in 3GPP TS 04.60/44.060. The GPRS support is indicated by the presence of the field GPRS Indicator in the SI Rest Octets (3GPP TS 04.08 / 3GPP TS 44.018, subclauses 10.5.2.34; 10.5.2.35, 10.5.2.36 and 10.5.2.37).
The following definitions are applicable to tests 20.22.1 to 20.22.33
- Carrier X supports GPRS : the SS includes the field GPRS Indicator in SI 3 Rest Octets and in SI 4 Rest Octets.
- The SS enables GPRS on carrier X : the SS starts including the field GPRS Indicator in SI 3 Rest Octets and in SI 4 Rest Octets.
- The SS disables GPRS on carrier X : the SS stops including the field GPRS Indicator in SI 3 Rest Octets and in SI 4 Rest Octets.
- Carrier X supports EC-GSM-IoT : the SS indicates the support of EC-GSM-IoT with the use of EC-SCH.
Unless otherwise stated in the method of test, in all of the tests of this subclause:
- The SIM is in the idle updated state in the default registration area with a TMSI and PTMSI assigned at the beginning of each test.
- By default idle paging is transmitted on the PCH according to 3GPP TS 04.08 / 3GPP TS 44.018, subclause 3.2.2.2.
- Where MS paging is specified within a test, TMSI is to be used on CCCH
- The Scheduling of System Information should be such that a complete set of consistent SI messages, including SI13 were applicable, can be decoded within 8 multiframes (8 51 frames).
- The Scheduling of EC System Information should be such that a complete set of consistent EC SI messages, can be decoded within 24 51-multiframes (3 x 8 51 frames).
- The MS is configured to automatically attach to GPRS at switch on by using the PICS/PIXIT Statement "Automatic GPRS attach procedure at switch on or power on Yes/No" as in GPRS Attach procedure tests (see subclause 44.2.1). For MS that does attach at power on, the SS shall accept access request with cause 'one phase access' in determining test verdict where applicable.
- The network simulation settings as specified in section 40 shall be applied unless otherwise stated in section 20.22.
Table 20.22.1: Default values of the system information or Packet Measurement Order fields
Parameter
3GPP TS 04.60 / 44.060 or 44.018 reference
Abbr.
Normal Setting
PRIORITY_CLASS
11.2.20
PC
1
HCS_THR
11.2.20
HT
-110dBm
GPRS_RESELECT_OFFSET
11.2.20
GRO
0 dB
NC_REPORTING_PERIOD_I
11.2.23
RP
61.44s
NETWORK_CONTROL_ORDER
11.2.23
NCO
NC0
CELL_RESELECT_HYST
11.2.20
CRH
0 dB
GPRS_TEMPORARY_OFFSET
11.2.20
GTO
0 db
GPRS_PENALTY_TIME
11.2.20
GPT
10s
GPRS_MS_TXPWR_MAX_CCH
11.2.20
GMTMC
Max. output power of MS
GPRS_RXLEV_ACCESS_MIN
11.2.20
GRAM
‑90 dBm
BA(GPRS) ARFCN
11.2.20
BA
All 0 except values in Table 20.22.1a (broadcast in in SYSTEM INFORMATION TYPE 2 and 2bis.)
PEO_DSC
11.7.2.37c
-
Not included if not stated otherwise
C1_DELTA_MIN
11.7.2.37c
-
Not included if not stated otherwise
C1_DELTA_MAX
11.7.2.37c
-
Not included if not stated otherwise
RCC
10.5.2.16
-
Not included if not stated otherwise
Table 20.22.1a: ARFCNs for Single Band Tests
Band
ARFCNs
GSM 450
259, 263, 269, 275, 279, 283, 287, 292
GSM 480
306, 310, 316, 322, 326, 330, 334, 339
GSM 710
441, 446, 452, 455, 461, 462, 466, 470, 477, 485, 493, 511
GSM 750
441, 446, 452, 455, 461, 462, 466, 470, 477, 485, 493, 511
T-GSM 810
441, 446, 452, 455, 461, 462, 466, 470, 477, 485, 493, 511
GSM 850
130, 136, 145, 152, 168, 170, 176, 177, 181, 185, 189, 193, 197, 207,219, 251
GSM 900
both P-GSM and E-GSM ARFCNs are broadcast:
GSM: 3, 9, 18, 25, 41, 43, 49, 50, 54, 58, 62, 66, 70, 80, 92, 124
E-GSM: 985, 989, 995, 1010, 1014
DCS 1800
512, 543, 568, 589, 602, 641, 662, 683, 696, 711, 732, 754, 794, 851, 870, 871, 872, 884
PCS1900
512, 543, 568, 589, 602, 629, 641, 653, 662, 683, 696, 711, 727, 732, 754, 777, 794, 809
Table 20.22.2: Default values of the EC-SI
Parameter
44.018 reference
Normal Setting
EC_RXLEV_ACCESS_MIN
9.1.43q
-110dBm
MS_TXPWR_MAX_CCH
9.1.43q
Max. output power of MS
C1_DELTA_MIN
9.1.43q
Default value = 3dB
C1_DELTA_MAX
9.1.43q
Default value = 9dB
BT_Threshold_DL
9.1.43q
-105 dBm
BT_Threshold_UL
9.1.43q
-105 dBm
EC_CELL_RESELECT_OFFSET
9.1.43q
0
NOTE: Parameters defined also for GPRS should have the same value as for GPRS values defined in 20.22 or 40 sections if not specified otherwise |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 20.22.2 Void |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.