hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.1.1.1 Conformance requirements: | The MS sends a DTAP LCS MO-LR invoke to the VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to the network containing a LCS-MOLR invoke com... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.1.1.2 Test Purpose | Verifies that a MS sends a correct LCS-MOLR Invoke message with the component MO_LR TYPE set to LocationEstimate and LCS_QoS value on the initiation of MOLR. On receipt of a RRLP Measure position request from SS to start the measurement, MS shall send back RRLP Measure Position Response to SS after finishing the measur... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.1.1.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Neighbor Cells: at least 2 neighbor cells are used with a minimum configuration of a BCCH. This is to allow the MS to perform the required ti... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.1.2 MO_LR Basic Self Location Request In Dedicated Mode (Normal case) | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.1.2.1 Conformance Requirement: | The MS sends a DTAP LCS MO-LR invoke to the VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO-LR by sending a REGISTER message to the network containing a LCS-MOLR invoke com... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.1.2.2 Test Purpose | Verifies that a MS sends a correct LCS-MOLR Invoke message on already established speech call related SACCH with the component MO_LR TYPE sets to LocationEstimate and LCS_QoS value on the initiation of MO_LR. On receipt of a RRLP Measure position request from SS to start the measurement, MS shall send back RRLP Measure... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.1.2.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: Default parameters.
Neighbor Cells: 2 neighbor cells are used with a minimum configuration of a BCCH. This is to allow
the MS to perform the required timing measurements.
Mobile Station:
The MS has valid TMSI and CKSN.
The MS is brought into the state U10 by using tab... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.2 MO_LR Transfer to 3rd Party | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.2.1 Conformance requirements: | The MS sends a DTAP LCS MO-LR invoke to the VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time). If the MS is requesting that its location be sent to another LCS client, the message shall include t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.2.2 Test Purpose | Verifies that a MS sends a correct LCS-MOLR Invoke message with the component MO_LR TYPE set to LocationEstimate, LCS_QoS value, LCS-ClientExternalID and MLC_Number (if available) on the initiation of MOLR. On receipt of a RRLP Measure position request from SS to start the measurement, MS shall send back RRLP Measure P... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.2.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Neighbor Cells: at least 2 neighbor cells are used with a minimum configuration of a BCCH. This is to allow the MS to perform the required t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.3 MO_LR Autonomous Location | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.3.1 Conformance Requirement | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting location assistance data, the message specifies the type of assistance data and the positioning method for which the assistance data applies.
The MS invokes a MO_LR by sending a REGISTER message to network containing a LCS-MOLR invoke component with M... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.3.2 Test Purpose | Verifies that a MS sends a correct LCS-MOLR Invoke message with the component MOLR Type set to Assistance Data, Location-Method sets to MS-Assisted EOTD, and LCS-QoS on the initiation of MO_LR. The MS shall acknowledge the reception of each assistance data component. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.3.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Mobile Station:
The MS is in MM-state "idle, updated" with valued TMSI and CKSN.
Specific PICS statements
-
PIXIT statements
-
Test Procedur... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4 MO_LR Positioning Measurement | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.1 MO_LR Positioning Measurement / Protocol Error | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.1.1 Conformance requirement: | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO_LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.1.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. The MS shall send a RRLP PROTOCOL ERROR message to SS with specific error code if RRLP MEASURE POSITION REQUEST is incomplete. On receipt of second RRLP MEASURE POSITION REQUEST from SS to start the measurement, MS shall send back ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.1.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Neighbor Cells: At least 2 neighbor cells are used with a minimum configuration of a BCCH. This is to allow the MS to perform the required t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.2 MO_LR Positioning Measurement /Location Error | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.2.1 Conformance requirement | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO_LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.2.2 Test Purpose | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall send back RRLP MEASURE POSITION RESPONSE message with Location Error component if the MS does not support the requested method. On receipt of second RRLP MEASURE POSITION REQUEST from SS to start the measurement, the MS sh... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.2.3 Method of Test | Initial Conditions:
System Simulator:
Serving Cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Neighbor Cells: At least 2 neighbor cells are used with a minimum configuration of a BCCH. This is to allow the MS to perform the required t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.3 MO_LR Positioning Measurement / Multiple RRLP REQUEST with same Reference Number | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.3.1 Conformance requirement | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO_LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.3.2 Test Purpose: | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall ignore the second RRLP MEASURE POSITION REQUEST if the second RRLP MEASURE POSITION REQUEST has the same REFERENCE NUMBER as in the previous one. The MS shall send back RRLP MEASURE POSITION RESPONSE to SS after finishing ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.3.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Neighbor Cells: at least 2 neighbor cells are used with a minimum configuration of a BCCH. This is to allow the MS to perform the required ti... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.4 MO_LR Positioning Measurement / Multiple RRLP REQUEST with different Reference Number | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.4.1 Conformance requirement | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO_LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.4.2 Test Purpose | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall terminate the current location measurement if the second RRLP MEASURE POSITION REQUEST is received with a different REFERENCE NUMBER. The MS shall perform the measurement according to the newly received RRLP MEASURE POSITI... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.4.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Neighbor Cells: at least 2 neighbor cells are used with a minimum configuration of a BCCH. This is to allow the MS to perform the required t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.5 MO_LR Positioning Measurement / RR Management Commands | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.5.1 Conformance requirement | The MS sends a DTAP LCS MOLR invoke to VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time).
The MS invokes a MO_LR by sending a REGISTER message to network containing a LCS-MOLR invoke component wi... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.5.2 Test Purpose | Verifies that a MS sends a correct positioning capability via control classmark sending. MS shall terminate the current location measurement if a RR MANAGEMENT command is received during the measurement procedure. The MS shall send a RR MANAGEMENT RESPONSE message to SS when the RR MANAGEMENT procedure is complete. The... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.3.4.5.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Neighbor Cells: at least 2 neighbor cells are used with a minimum configuration of a BCCH. This is to allow the MS to perform the required ti... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4 Mobile Terminated Location Request for Mobiles supporting MS-Assisted EOTD | The test cases in this sub clause focus on Mobile Terminated Location Request. A MT-LR occurs when an external LCS client requests the position of an MS by sending the SS REGISTER message. This may be sent to request verification for a particular MT-LR or simply to notify the user about an MT-LR that has already been a... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.1 MT-LR Location Notification for MS-Assisted EOTD | Location notification takes place to inform the MS user that a particular LCS client is requesting their position without seeking the user's permission. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.1.1 Conformance requirements: | The following requirements apply for this test:
1. On receipt of a REGISTER message containing the LCS Notification Invoke component with notificationType set to notifyLocationAllowed. The MS shall notify the MS user of the location request using the method defined in the manufacturers' specification.
2. The MS shall t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.1.2 Test Purpose | Verifies that when the MS receives a REGISTER message, containing a LCS Location Notification Invoke component set to notifyLocationAllowed, the MS displays information about the LCS client correctly (as defined by the individual manufacturer) and sends a RELEASE COMPLETE message containing a LocationNotification retur... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.1.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Mobile Station:
The MS is in MM-state "idle, updated" with valued TMSI and CKSN.
Test Procedure:
The MS is paged with a PAGING REQUEST TYPE 1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.2 MT-LR Privacy Options for Mobiles supporting MS-Assisted EOTD | Privacy options are used in conjunction with the MS subscription profile on the VLR. They give the MS user the option to grant or withhold permission for individual location requests as they occur. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.2.1 MT-LR Privacy Options/ Verification – Location Allowed If No Response for mobiles supporting MS-Assisted EOTD | The case occurs when the target MS subscription profile on the VLR is set to location allowed if no response is sent. This is the default option if the VMSC does not receive verification from the target MS within a predetermined time. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.2.1.1 Conformance requirements | The following requirements apply for this test:
1. On receipt of a REGISTER message containing the LCS Notification Invoke component with notificationType set to notifyAndVerify-LocationAllowedIfNoResponse. The MS a) notifies the user of the request and b) indicates the default is location allowed if no response is rec... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.2.1.2 Test Purpose | Verifies that when the MS receives a REGISTER message, containing a LCS Location Notification Invoke component set to notifyAndVerify-LocationAllowedIfNoResponse, the MS displays information about the LCS client correctly and indicates that the default response is location allowed if no response is sent. Gives the user... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.2.1.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Mobile Station:
The MS is in MM-state "idle, updated" with valued TMSI and CKSN.
Test Procedure:
The MS is paged with a PAGING REQUEST TYPE 1... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.2.2 MT-LR Privacy Options/ Verification – Location Not Allowed If No Response for Mobiles supporting MS-Assisted EOTD | This case occurs when the target MS subscription profile on the VLR is set to location not allowed if no response is sent. This is the default option if the VMSC does not receive verification from the target MS within a predetermined time. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.2.2.1 Conformance requirements: | The following requirements apply for this test:
1. On receipt of a REGISTER message containing the LCS Notification Invoke component with notificationType set to notifyAndVerify-LocationAllowedIfNoResponse. The MS a) notifies the user of the request and b) indicates that the default is location not allowed if no respon... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.2.2.2 Test Purpose | Verifies that when the MS receives a REGISTER message, containing a LCS Location Notification Invoke component set to notifyAndVerify-LocationNotAllowedIfNoResponse, the MS displays information about the LCS client correctly and indicates that the default response is location not allowed if no response is sent. Gives t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.4.2.2.3 Method of Test | Initial Conditions
System Simulator:
Serving cell: Default parameters, in SYSTEM INFORMATION TYPE 3 (SI3 Rest Octet) the early classmark sending control is implemented in the SS.
Mobile Station:
The MS is in MM-state "idle, updated" with valued TMSI and CKSN.
Test Procedure
The MS is paged with a PAGING REQUEST TYPE 1 ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.5 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6 E-OTD Timing Measurement Accuracy | Scope of Tests
This test procedure plan is intended verify the operation of Enhanced Observed Timing Difference (E-OTD) measurement functionality from an E-OTD capable GSM Mobile Station (MS).
The scope of this test plan is limited to verification of the MS physical layer against 3GPP TS 05.05, Release 1999, version 8.... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1 E-OTD Accuracy, Sensitivity Performance Tests using GMSK Signals | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving a neighbor shall not exceed 100 nanoseconds and 300 nanoseconds at a minimum neighbor carrier signal strength relative to relative sensitivity levels of 12 dB and –8 dB respectively, as specified in 3GPP TS 05.05, annex I, sub clause I.2.1, table I.2.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. Nearby neighbor stations that provide a relatively high C/N to the MS receiver should result in greater measurement accuracy than those further away wit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.4 Method of Test | Initial Configuration
Neighbor Cell: One neighbor cells with a minimum configuration of a BCCH in order to allow the MS to perform the required measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List.
Assistance Data: The assistance data listed in Table 70.6.1-1 and Tab... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.5 Test procedure | a) Configure serving base station simulator to transmit GMSK dummy bursts in time slots 1 through 7.
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dB.
c) Disable the interfering signal generator.
d) Configure the neighbor base station simulator s... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.1.6 Test Requirements | Verify that the RMS90 error calculated for each procedure in 70.6.1.5 is within the test conformance requirements listed in Table 70.6.1-3
Table 70.6.1-3, Test Conformance Requirements
Procedure
RMS90 error, 3GPP TS 05.05,
Annex I, Minimum Performance Requirement
RMS90 error, 3GPP TS 51.010, 70.6.1, Test Conformance Re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2 E-OTD Accuracy, Interference Performance Tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving an 8PSK neighbor with a co-channel interference ratio of 0 dB shall not exceed 300 nanoseconds, 10dB not exceeding 300 nanoseconds, adjacent channel interference ratio of –18dB not exceeding 500 nanoseconds, -8 dB not exceeding 200 nanoseconds, as well as an ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. As the C/I ratio due to neighbor cell co-channel interference is reduced, E-OTD measurement accuracy may be reduced as well.
The purpose of this test c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.4 Method of Test | Initial Configuration
Neighbor Cells: at least two neighbor cells with a minimum configuration of a BCCH in order to allow the mobile to perform the required accuracy measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.5 Test procedure | Co-Channel test procedure at 0dB C/I:
a) Configure serving base station simulator to transmit GMSK dummy bursts in time slots 1 through 7
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm
c) Enable the interfering signal generator on the frequenc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.2.6 Test Requirements | Verify that the RMS90 error calculated for each procedure in 70.6.2.5 is within the test conformance requirements listed in Table 70.6.2-1.
Table 70.6.2-1, Test Conformance Requirements
Procedure
RMS90 error, 3GPP TS 05.05,
Annex I, Minimum Performance Requirement
RMS90 error, 3GPP TS 51.010, 70.6.2, Test Conformance R... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving a TU3 Rayleigh-faded neighbor shall not exceed 1.5 microseconds, as specified in 3GPP TS 05.05, Release 99, Version 8.7.1, Annex I, Clause I.2.3, Table I.2.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. Rayleigh fading to the neighbor cell will reduce E-OTD measurement accuracy.
The purpose of this test case is to verify that an E-OTD capable MS can pr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.4 Method of Test | Initial Configuration
Neighbor Cell: at least one neighbor cell with a minimum configuration of a BCCH in order to allow the mobile to perform the required accuracy measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List.
Assistance Data: The assistance data listed in Ta... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.5 Test procedure | a) Configure serving base station simulator to transmit GMSK dummy bursts in time slots 1 through 7
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm
c) Disable the interfering signal generator
d) Configure the neighbor base station simulator suc... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.3.6 Test Requirements | Verify that the RMS90 error calculated in Step i) is < 1.5 microseconds |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4 E-OTD Accuracy, Interference Performance Tests, 8PSK BCCH | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4.4 Method of Test | Initial Configuration
Neighbor Cells: at least one neighbor cell with a minimum configuration of a BCCH in order to allow the mobile to perform the required accuracy measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4.5 Test procedure | Co-Channel 8PSK test procedure at 0dB C/I:
a) Configure serving base station simulator to transmit in time slots 1 through 7
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm
c) Enable the interfering signal generator on the frequency of the nei... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.4.6 Test Requirements | Verify that the RMS90 error calculated for each procedure in 70.6.4.5 is within the test conformance requirements listed in Table 70.6.4-1
Table 70.6.4-1, Test Conformance Requirements
Procedure
RMS90 error, 3GPP TS 05.05,
Annex I, Minimum Performance Requirement
RMS90 error, 3GPP TS 51.010, 70.6.4, Test Conformance Re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5 E-OTD Accuracy, Multipath Performance Test, 8PSK BCCH | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving a TU3 Rayleigh-faded 8PSK-modulated neighbor shall not exceed 1.5 microseconds, as specified in 3GPP TS 05.05, Release 99, Annex I, Clause I.2.3, Table I.2.3 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. Rayleigh fading to the neighbor cell will reduce E-OTD measurement accuracy.
The purpose of this test case is to verify that an E-OTD capable MS can pr... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.4 Method of Test | Initial Configuration
Neighbor Cells: At least one neighbor cell with a minimum configuration of a BCCH in order to allow the mobile to perform the required accuracy measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List.
Assistance Data: The assistance data listed in Ta... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.5 Test procedure | a) Configure serving base station simulator to transmit 8PSK bursts modulated with pseudo-random data in time slots 1 through 7
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm
c) Disable the interfering signal generator
d) Configure the neighbo... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.5.6 Test Requirements | Verify that the RMS90 error calculated in Step i) is < 1.5 microseconds |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6 E-OTD Accuracy, Sensitivity Performance Tests for 8PSK Modulated signals | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.1 Definition | Enhanced Observed Timing Difference is a mechanism intended to provide location information from an MS within a GSM network. E-OTD measures the burst timing alignment between the serving cell for the MS and a minimum of two neighbor cells. The observed timing difference, along with the BSIC or Cell ID of each neighbor ... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.2 Conformance requirement | The RMS90 measurement error of an E-OTD capable MS receiving a neighbor shall not exceed 100 nanoseconds and 300 nanoseconds at a minimum neighbor carrier signal strength relative to relative sensitivity levels of 12 dB and –8 dB respectively, as specified in 3GPP TS 05.05, annex I, sub clause I.2.1, table I.2.1 |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.3 Test purpose | E-OTD measurement accuracy is heavily influenced by the type of RF environment available to the MS at the time a Measure Position Request is received from the network. Nearby neighbor stations that provide a relatively high C/N to the MS receiver should result in greater measurement accuracy than those further away wit... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.4 Method of Test | Initial Configuration
Neighbor Cell: One-neighbor cells with a minimum configuration of a BCCH in order to allow the MS to perform the required measurements. The neighbor BCCH shall be included in the serving BCCH System Information Neighbor List.
Assistance Data: The assistance data listed in Table 70.6.6-1 and Tab... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.5 Test procedure | a) Configure serving base station simulator to transmit 8PSK bursts in time slots 1 through 7.
b) Establish RF connectivity between the E-OTD compatible MS and its serving base station simulator, verify RSSI of -80 dBm.
c) Disable the interfering signal generator.
d) Configure the neighbor base station simulator such t... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.6.6.6 Test Requirements | Verify that the RMS90 error calculated for each procedure in 70.6.6.5 is within the test conformance requirements listed in Table 70.6.6-3
Table 70.6.6-3, Test Conformance Requirements
Procedure
RMS90 error, 3GPP TS 05.05,
Annex I, Minimum Performance Requirement
RMS90 error, 3GPP TS 51.010, 70.6.6, Test Conformance Re... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7 Assisted GPS Network Induced Tests | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.1 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.2 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.3 Void | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4 Network Induced Location Request Emergency Call on TCH Radio Channel | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.1 Network Induced Location Request Emergency Call on TCH Radio Channel for Mobiles Supporting MS-Based GPS | |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.1.1 Conformance requirements | 1. With the MS in the "idle, updated" state, the user shall initiate an emergency after the number 112 (for GSM900 and 1800 MS), or 911 (for PCS 1900 MS in the USA), or 08 (for PCS 1900 MS in Mexico) has been entered by the user. The MS shall send a CHANNEL REQUEST message with correct establishment cause ("emergency c... |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.1.2 Test Purpose | To verify when a network instigates the LCS positioning procedure by sending RRLP (Measure Position Request) message, after a traffic channel has been established during an emergency call, the mobile responds with RRLP (Measure Position Response) containing MS location estimate. |
683b5b8a98f7b1390ddd5516ea9247a2 | 51.010-1 | 70.7.4.1.3 Method of Test | Initial Conditions
System Simulator (SS):
Serving Cell: default parameters.
Satellite signals: default conditions.
Mobile Station (MS):
The MS is in MM-state “idle, updated” with valued TMSI and CKSN.
SIM:
Normal SIM
Specific PICS statements
- TSPC_MS_RRLP_RELEASE
PIXIT statements
-
Test Procedure
An Emergency Call is ... |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.