hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.1.3 Test purpose | The purpose of this test is to verify the requirement for the uplink synchronization control during intra-frequency handover in CELL_DCH state in minimum requirement . |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.1.4 Initial conditions | The test parameters are given in Table 8.5.3.2.2.2 and 8.5.3.2.2.3 as below. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration with activation time "now" at the beginning of T3 with a new active cell, cell 2, after the UE has reported event 1G. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table 8.5.3.2.2.2: General test parameters for intra-frequency handover
Parameter
Unit
Value
Comment
DPCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2.2 and A.2.1.2
Power Control
On
Target quality value on DPCH
BLER
0.01
Initial conditions
Active cell
Cell 1
In the case of multi-frequency network, the UE has a RRC connection on the primary frequency in cell 1.
Neighbouring cell
Cell 2
Final condition
Active cell
Cell 2
In the case of multifrequency network, UE will handover to the primary frequency in cell 2.
O
dB
0
cell-individual-offset
The value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
T1
s
5
T2
s
5
T3
s
5
Table 8.5.3.2.2.3: Cell specific test parameters for intra-frequency handover
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note3)
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
Note1
n.a.
OCNS_Ec/Ior
dB
-3
Note2
dB
3
3
3
dBm/1.28 MHz
-70
PCCPCH_RSCP
dBm
-70
n.a.
n.a.
Propagation Condition
AWGN
Parameter
Unit
Cell 2
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note3)
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
n.a.
Note1
OCNS_Ec/Ior
dB
-3
Note2
dB
-Inf.
6
-Inf.
6
-Inf.
6
dBm/1.28 MHz
-70
PCCPCH_RSCP
dBm
-Inf.
-67
n.a.
n.a.
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
Note 3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.1.5 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time “now”.
8) After 5 seconds, the SS shall switch the power settings from T2 to T3
9) The UE transmits the UL DPCH to cell 2 less than 1 s from the beginning of time period T3 and UTRAN measures the initial uplink synchronization timing position of the first UL DPCH on cell2 and compares it with the desired position. If the timing deviation is less than the accuracy requirement as specified in Table 8.5.3.2.2.4, the number of successful tests is increased by one. And UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat step 1-10 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
2
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 2)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: The SFN-CFN observed time difference is calculated from the OFF and Tm parameters contained in the IE "Cell synchronisation information ", TS 25.331, clause 10.3.7.6. According to TS 25.331, 8.6.7.7, this IE is included in MEASUREMENT REPORT if IE "Cell synchronisation information reporting indicator" in IE "Cell reporting quantities" TS 25.331, clause 10.3.7.5 is set to TRUE in MEASUREMENT CONTROL.
Note 2: Reporting interval = 0 ms means no periodical reporting
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
30 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-TDD
1,28 Mcps TDD
-UL target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
--1,28 Mcps TDD
1
-TPC step size
1
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
9 dB
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
2
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
- SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot code list
1
-Channelisation code
8/1
-Choice more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
- TSTD indicator (10.3.6.85a)
TRUE
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
TSTD indicator
TRUE
-Cell parameters ID
0
-SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
-DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes (10.3.6.32)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
-SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot channelisation codes (10.3.6.17)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/2
-CHOICE more timeslots
No more timeslots
-SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message for Intra frequency test cases
This message is common for all intra frequency test cases in clause 8.7 and is described in Annex I. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.1.6 Test requirements | The UE shall not exceed the accuracy requirements as Table 8.5.3.2.2.4.
Table 8.5.3.2.2.4: Uplink synchronisation control accuracy requirements
Parameter
Unit
Accuracy [chip]
Conditions
Io [dBm/ 1.28 MHz]
Uplink synchronization control during handover
chip
+/- 0.5
-94...-50
The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.2 Scenario 2: Handover to inter-frequency cell | This test case is applicable for UE handovers in single frequency network and UE handovers from primary frequency to secondary frequency in multi-frequency network. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.2.1 Definition and applicability | The closed loop uplink synchronisation control uses layer 1 symbols (SS commands) for DPCH and PUSCH. After establishment of the uplink synchronisation, NodeB and UE start to use the closed loop UL synchronisation control procedure. This procedure is continuous during connected mode.
During a handover the UE shall transmit in the new cell with timing advance TA adjusted by the relative timing difference t between the new and the old cell if indicated by higher layers:
TAnew = TAold + 2t.
TAnew is the timing advance of the new cell.
TAold is the timing advance of the old cell,
t is the relative timing difference between the new and the old cell, which is measured by UE as SFN-SFN observed time difference type 2.
The uplink synchronization accuracy during handover is defined as timing deviation between the initial actual uplink synchronization position and the desired position of the first uplink DPCH on the target cell.
The requirements and this test apply to all types of 1.28 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.2.2 Minimum requirement | The UE shall not exceed the accuracy requirements as Table 8.5.3.2.2.5.
Table 8.5.3.2.2.5: Uplink synchronisation control accuracy requirements
Parameter
Unit
Accuracy [chip]
Conditions
Io [dBm/ 1.28 MHz]
Uplink synchronization control during handover
chip
+/- 0.5
-94...-50
The rate of correct uplink synchronisation control observed during repeated tests shall be at least 90% with a confidence level of 95%. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.2.4 Initial conditions | The test parameters are given in Table 8.5.3.2.2.6 and 8.5.3.2.2.7 as below. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration with activation time "now" at the beginning of T3 with a new active cell, cell 2, after the UE has reported event 1G. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table 8.5.3.2.2.6: General test parameters for inter-frequency handover
Parameter
Unit
Value
Comment
DPCH parameters
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2.2 and A.2.1.2
Power Control
On
Target quality value on DPCH
BLER
0.01
Initial conditions
Active cell
Cell 1
The UE has a RRC connection on the secondary frequency in cell 1.
Neighbour cell
Cell 2
Final conditions
Active cell
Cell 2
The UE will handover to the primary frequency in cell 2.
Threshold non used frequency
dBm
-75
Absolute RSCP threshold for event 2C
O
dB
0
cell-individual-offset
The value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
6 TDD neighbours on Channel 2
T1
s
5
T2
s
10
T3
s
5
Table 8.5.3.2.2.7: Cell Specific parameters for inter-frequency handover
Parameter
Unit
Cell 1
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
UTRA RF Channel Number(Note 4)
Channel 2
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
Note1
n.a.
OCNS_Ec/Ior
dB
-3
Note2
dB
3
3
3
dBm/1.28 MHz
-70
PCCPCH_RSCP
dBm
-70
n.a.
n.a.
Propagation Condition
AWGN
Parameter
Unit
Cell 2
Timeslot Number
0
DwPTS
5
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number(Note 3)
Channel 1
UTRA RF Channel Number(Note 4)
Channel 2
PCCPCH_Ec/Ior
dB
-3
n.a.
DwPCH_Ec/Ior
0
DPCH_Ec/Ior
dB
n.a.
n.a.
n.a.
Note1
OCNS_Ec/Ior
dB
-3
Note2
dB
-Inf.
4
-Inf.
4
-Inf.
4
dBm/1.28 MHz
-70
PCCPCH_RSCP
dBm
-Inf.
-69
n.a.
n.a.
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior .
Note3: The UTRA RF Channel Number is the primary frequency’s channel number.
Note4: The UTRA RF Channel Number is the secondary frequency’s channel number. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.2.5 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.3.4.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G.
7) SS shall transmit a PHYSICAL CHANNEL RECONFIGURATION message with activation time “now”.
8) After 10 seconds, the SS shall switch the power settings from T2 to T3
9) The UE transmits the UL DPCH to cell 2 less than 1 s from the beginning of time period T3 and UTRAN measures the initial uplink synchronization timing position of the first UL DPCH on cell2 and compares it with the desired position. If the timing deviation is less than the accuracy requirement as specified in Table 8.5.3.2.2.4, the number of successful tests is increased by one. And UE shall transmit a PHYSICAL CHANNEL RECONFIGURATION COMPLETE message on the UL DCCH of cell 2.
10) After 5 seconds, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
11) Repeat steps1-10 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message, event 2C (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
TRUE (Note 1)
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
2
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 2)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: The SFN-CFN observed time difference is calculated from the OFF and Tm parameters contained in the IE "Cell synchronisation information ", TS 25.331, clause 10.3.7.6. According to TS 25.331, 8.6.7.7, this IE is included in MEASUREMENT REPORT if IE "Cell synchronisation information reporting indicator" in IE "Cell reporting quantities" TS 25.331, clause 10.3.7.5 is set to TRUE in MEASUREMENT CONTROL.
Note 2: Reporting interval = 0 ms means no periodical reporting
PHYSICAL CHANNEL RECONFIGURATION message (step 7):
Information Element
Value/Remark
Message Type
UE Information Elements
-RRC transaction identifier
0
-Integrity check info
Not Present
-Integrity protection mode info
Not Present
-Ciphering mode info
Not Present
-Activation time
At T3
-New U-RNTI
Not Present
-New C-RNTI
Not Present
-RRC State Indicator
CELL_DCH
-UTRAN DRX cycle length coefficient
Not Present
CN Information Elements
-CN Information info
Not Present
UTRAN mobility information elements
-URA identity
Not Present
RB information elements
-Downlink counter synchronisation info
Not Present
-RB with PDCP information list
Not Present
-RB with PDCP information
Not Present
PhyCH information elements
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN (Nt)
Same UARFCN as used for cell 2
Uplink radio resources
-Maximum allowed UL TX power
30 dBm
-CHOICE channel requirement
Uplink DPCH info
-Uplink DPCH info (10.3.6.88)
-Uplink DPCH power control info (10.3.6.91)
-CHOICE mode
TDD
-TDD
1,28 Mcps TDD
-UL target SIR
Not Present
-CHOICE UL OL PC info
Individually signalled
-CHOICE TDD option
--1,28 Mcps TDD
1
-TPC step size
1
-CHOICE mode
TDD
-Uplink timing advance control (10.3.6.96)
-CHOICE Timing Advance
Disabled
-UL CCTrCH list
1
-UL Target SIR
9 dB
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Uplink DPCH timeslots and codes (10.3.6.94)
-Dynamic SF Usage
False
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
2
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-Choice TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
- SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot code list
1
-Channelisation code
8/1
-Choice more timeslots
No more timeslots
Downlink radio resources
-CHOICE mode
TDD
-Downlink information common for all radio links (10.3.6.24)
-Downlink DPCH info common for all RL (10.3.6.18)
-Timing indicator
Initialise
-CFN-targetSFN frame offset
Not Present
-Downlink DPCH power control information (10.3.6.23)
-CHOICE mode
TDD
-TPC Step size
1 dB
-CHOICE mode
TDD
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
- TSTD indicator (10.3.6.85a)
TRUE
-Default DPCH Offset Value (10.3.6.16)
0
-Downlink information per radio link list
1
-Downlink information for each radio link (10.3.6.27)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps
TSTD indicator
TRUE
-Cell parameters ID
0
-SCTD indicator
False
-Downlink DPCH info for each RL (10.3.6.21)
-CHOICE mode
TDD
-DL CCTrCH list
1
-TFCS ID
Not Present
-Time Info (10.3.6.83)
-Activation Time
now
-Duration
Infinite
-Common timeslot info
Not Present
-Downlink DPCH timeslots and codes (10.3.6.32)
-First individual timeslot info (10.3.6.37)
-Timeslot Number (10.3.6.84)
-CHOICE TDD option
1,28 Mcps
-Timeslot number
5
-TFCI existence
True
-Midamble shift and burst type (10.3.6.41)
-CHOICE TDD option
1,28 Mcps
-Midamble Allocation Mode
Default
-Midamble configuration
16
-Midamble shift
Not present
-CHOICE TDD option
1,28 Mcps
-Modulation
QPSK
-SS-TPC Symbols
-Additional TPC-SS Symbols
-First timeslot channelisation codes (10.3.6.17)
-CHOICE codes representation
Consecutive codes
-First channelisation code
16/1
-Last channelisation code
16/2
-CHOICE more timeslots
No more timeslots
-SCCPCH information for FACH (10.3.6.70)
Not Present
MEASUREMENT REPORT message for Inter frequency test cases
This message is common for all inter frequency TDD test cases in clause 8.7 and is described in Annex I. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.2.2.2.6 Test requirements | The UE shall not exceed the accuracy requirements as Table 8.5.3.2.2.8.
Table 8.5.3.2.2.8: Uplink synchronisation control accuracy requirements
Parameter
Unit
Accuracy [chip]
Conditions
Io [dBm/ 1.28 MHz]
Uplink synchronization control during handover
chip
+/- 0.5
-94...-50
The rate of correct handovers observed during repeated tests shall be at least 90% with a confidence level of 95%. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.5.3.3 7.68 Mcps TDD option | Void. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6 UE Measurements Procedures | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1 TDD intra frequency measurements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1 Event 1G triggered reporting in AWGN propagation conditions | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.1.1 3,84 Mcps TDD Option | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This measurement reporting delay excludes a delay uncertainty resulted when inserting the measurement report to the TTI of the uplink DCCH. The delay uncertainty is twice the TTI of the uplink DCCH.
The requirements and this test apply to the TDD (3,84 Mcps option) UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.1.2 1,28 Mcps TDD Option | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This measurement reporting delay excludes a delay uncertainty resulted when inserting the measurement report to the TTI of the uplink DCCH. The delay uncertainty is twice the TTI of the uplink DCCH.
The requirements and this test apply to the 1.28 Mcps option TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.1.3 7,68 Mcps TDD Option | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This measurement reporting delay excludes a delay uncertainty resulted when inserting the measurement report to the TTI of the uplink DCCH. The delay uncertainty is twice the TTI of the uplink DCCH.
The requirements and this test apply to the TDD (7,68 Mcps option) UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.2.1 3,84 Mcps TDD Option | The UE shall be able to identify a new detectable intra-frequency TDD cell belonging to the monitored set within Tidentify intra ms, where Tidentify intra = 800 ms.
When L3 filtering is used, an additional delay can be expected.
In CELL_DCH state, the UE shall be capable of performing P-CCPCH RSCP measurements for Xmeasurement intra identified intra-frequency TDD cells of the monitored set with a measurement period for intra-frequency P-CCPCH RSCP measurements Tmeasurement period intra, where
Xmeasurement intra = 6 (cells)
Tmeasurement period intra = 200 ms
The UE physical layer shall be capable of reporting these measurements to higher layers with the measurement period Tmeasurement period intra.
If the UE has identified more than Xmeasurement intra intra-frequency TDD cells, the UE shall perform measurements of all identified cells but the reporting rate of P-CCPCH RSCP measurements of cells from the UE physical layer to higher layers may be decreased.. The measurement accuracy for all measured cells shall be as specified in the section 9.
The normative reference for this requirement is TS 25.123 [2] clauses 8.1.2.2.1, 8.1.2.2.2 and A.8.1.1 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.2.2 1,28 Mcps TDD Option | The UE shall be able to identify a new intra frequency TDD cell belonging to the monitored set within
ms
Tbasic_identify_TDD, intra = 800 ms. This is the time period used in the intra frequency equation where the maximum allowed time for the UE to identify a new TDD cell is defined.
NPeriod,Intra: = 40 Number of subframes in TMeasurement_Period, Intra.
NIntra : This is the minimum number of sub-frame in that the period of TS0, DwPTS and main guard period is available for intra frequency measurements, during the measurement period.
TMeasurement_Period, Intra = 200 ms. The measurement period for Intra frequency P-CCPCH RSCP measurements.
If a cell belonging to monitored set has been detectable at least for the time period Tidentify_intra and then enters or leaves the reporting range, the event triggered measurement reporting delay shall be less than 200ms when the L3 filter has not been used and the UE P-CCPCH measurement capabilities of Section 8.1A.2.2.2 in [2] are valid.
The event triggered measurement reporting delay on cells not belonging to monitored set, measured without L3 filtering, shall be less than the above defined Tidentify detected set. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.2.3 7,68 Mcps TDD Option | The UE shall be able to identify a new detectable intra-frequency TDD cell belonging to the monitored set within Tidentify intra ms, where Tidentify intra = 800 ms.
When L3 filtering is used, an additional delay can be expected.
In CELL_DCH state, the UE shall be capable of performing P-CCPCH RSCP measurements for Xmeasurement intra identified intra-frequency TDD cells of the monitored set with a measurement period for intra-frequency P-CCPCH RSCP measurements Tmeasurement period intra, where
Xmeasurement intra = 6 (cells)
Tmeasurement period intra = 200 ms
The UE physical layer shall be capable of reporting these measurements to higher layers with the measurement period Tmeasurement period intra.
If the UE has identified more than Xmeasurement intra intra-frequency TDD cells, the UE shall perform measurements of all identified cells but the reporting rate of P-CCPCH RSCP measurements of cells from the UE physical layer to higher layers may be decreased.. The measurement accuracy for all measured cells shall be as specified in the section 9.
The normative reference for this requirement is TS 25.123 [2] clauses 8.1B.2.2.1, 8.1B.2.2.2 and A.8.1.1 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.3 Test purpose | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.3.1 3,84 Mcps TDD Option | To verify that the UE meets the minimum requirement. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.3.2 1,28 Mcps TDD Option | To verify the UE meets the minimum requirements. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.3.3 7,68 Mcps TDD Option | To verify the UE meets the minimum requirements. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.4.1 3,84 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.4.1.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Table 8.6.1.1.1 and 8.6.1.1.2. The test consists of three successive time periods, with time durations of T1, T2 and T3 respectively. Three cells shall be present in the test, cell 1 being the serving cell and cell 2 and cell 3 being neighbour cells on the used frequency. All cells shall be synchronised, i.e. share the same frame and timeslot timing.
In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP shall be reported together with Event 1G. The Measurement control message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T1 is at least equal to the RRC procedure delay as defined in [9].
The second Beacon timeslot shall be provided in timeslot 8 for both cell 1 and cell 2. The DL DPCH shall be transmitted in timeslot 2 and the UL DPCH shall be transmitted in timeslot 10. The TTI of the uplink DCCH shall be 20ms.
Table 8.6.1.1.1: General test parameters for Event 1G triggered reporting in AWGN propagation condition
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2, Cell 3
Final condition
Active cell
Cell 1
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Threshold used frequency
dBm
-70
Applicable for Event 1G
Filter coefficient
0
Monitored cell list size
12 TDD neighbours on Channel 1
T1
s
6
T2
s
6
T3
s
6
Table 8.6.1.1.2: Cell specific parameters for Event 1G triggered correct reporting in AWGN propagation condition
Parameter
Unit
Cell 1
Cell 2
Cell 3
T1
T2
T3
T1
T2
T3
T1
T2
T3
DL timeslot number
0
0
0
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
SCH_toffset
0
5
10
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
dB
7
5
5
7
-Inf
-Inf
7
PCCPCH RSCP
dBm
-66
-68
-68
-66
-Inf
-Inf
-66
dBm / 3,84 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.4.1.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 6 seconds from the beginning of T1, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G for cell 2. The measurement reporting delay from the beginning of T2 shall be less than 240 ms. If the UE fails to report the event within the required delay, then a failure is recorded. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
7) After 6 seconds from the beginning of T2, the SS shall switch the power settings from T2 to T3.
8) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G for cell 3. The measurement reporting delay from the beginning of T3 shall be less than 840 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
9) After 6 seconds from the beginning of T3, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
10) Repeat steps 1-9 [TBD] times.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
1
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: Reporting interval = 0 ms means no periodical reporting
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1G
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 2
MEASUREMENT REPORT message (step 8)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 3
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1G
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 3 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.4.2 1,28 Mcps TDD Option | Test environment : normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested : mid range ;see clauses G.2.4.
The test parameters are given in Table 8.6.1.1.4A and 8.6.1.1.4B below. The test consists of three successive time periods, with time durations of T1, T2 and T3 respectively. Three cells shall be present in the test, cell 1 being the serving cell and cell 2 and cell 3 being neighbour cells on the used frequency. All cells shall be synchronised, i.e. share the same frame and timeslot timing.
In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP shall be reported together with Event 1G reporting. The Measurement control message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T1 is at least equal to the RRC procedure delay as defined in [9]. The cell specific test parameters are given in Table 8.6.1.1B below.
The TTI of the uplink DCCH shall be 40ms.
Table 8.6.1.1.4A: General test parameters for Event 1G triggered reporting in AWGN propagation condition 1,28Mcps option
Parameter
Unit
Value
Comment
DPCH parameters active cell
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A. The DPCH is located in an other timeslot than 0
Power Control
On
Target quality value on DTCH
BLER
0.01
Active cell
Cell 1
Neighbour cell
Cell 2, Cell 3
O
DB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
DB
0
Time to Trigger
Ms
0
Filter coefficient
0
Monitored cell list size
12 TDD neighbours on Channel 1
T1
S
6
T2
S
6
T3
S
6
Table 8.6.1.1.4B: Cell specific parameters for Event 1G triggered correct reporting in AWGN propagation condition 1,28 Mcps option
Parameter
Unit
Cell 1
Cell 2
Cell 3
DL timeslot number
0
DwPTS
0
DwPTS
0
DwPTS
T1
T2
T3
T1
T2
T3
T1
T2
T3
T1
T2
T3
T1
T2
T3
T1
T2
T3
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
dB
7
4
7
4
4
7
-Inf
4
7
-Inf
-Inf
7
-Inf
7
PCCPCH RSCP
dBm
-66
-69
-69
-66
-Inf
-Inf
-66
dBm / 1,28 MHz
-70
Propagation Condition
AWGN
NOTE: The DPCH of all cells are located in a timeslot other than 0.
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 6 seconds from the beginning of T1, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G for cell 2. The measurement reporting delay from the beginning of T2 shall be less than 280 ms. If the UE fails to report the event within the required delay, then a failure is recorded. If the reporting delay for this event is within the required limit, the number of successful tests is increased by one.
7) After 6 seconds from the beginning of T2, the SS shall switch the power settings from T2 to T3.
8) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G for cell 3. The measurement reporting delay from the beginning of T3 shall be less than 880 ms. If the reporting delay for this event is within the required limit, the number of successful tests is increased by one.
9) After 6 seconds from the beginning of T3, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
10) Repeat steps 1-9 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the default message content in clause 9 of 34.108 [3], with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
1
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: Reporting interval = 0 ms means no periodical reporting
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1G
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD Option
1.28 Mcps TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 2
MEASUREMENT REPORT message (step 8)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 3
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1G
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD Option
1.28 Mcps TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 3 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.4.3 7,68 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.4.3.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Table 8.6.1.1.4.3.1.1 and 8.6.1.1.4.3.1.2. The test consists of three successive time periods, with time durations of T1, T2 and T3 respectively. Three cells shall be present in the test, cell 1 being the serving cell and cell 2 and cell 3 being neighbour cells on the used frequency. All cells shall be synchronised, i.e. share the same frame and timeslot timing.
In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP shall be reported together with Event 1G. The Measurement control message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T1 is at least equal to the RRC procedure delay as defined in [9].
The second Beacon timeslot shall be provided in timeslot 8 for both cell 1 and cell 2. The DL DPCH shall be transmitted in timeslot 2 and the UL DPCH shall be transmitted in timeslot 10. The TTI of the uplink DCCH shall be 20ms.
Table 8.6.1.1.4.3.1.1: General test parameters for Event 1G triggered reporting in AWGN propagation condition
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2, Cell 3
Final condition
Active cell
Cell 1
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
0
Threshold used frequency
dBm
-70
Applicable for Event 1G
Filter coefficient
0
Monitored cell list size
12 TDD neighbours on Channel 1
T1
s
6
T2
s
6
T3
s
6
Table 8.6.1.1.4.3.1.2: Cell specific parameters for Event 1G triggered correct reporting in AWGN propagation condition
Parameter
Unit
Cell 1
Cell 2
Cell 3
T1
T2
T3
T1
T2
T3
T1
T2
T3
DL timeslot number
0
0
0
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
SCH_toffset
0
5
10
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
dB
7
5
5
7
-Inf
-Inf
7
PCCPCH RSCP
dBm
-66
-68
-68
-66
-Inf
-Inf
-66
dBm / 7,68 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.4.3.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 6 seconds from the beginning of T1, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G for cell 2. The measurement reporting delay from the beginning of T2 shall be less than 240 ms. If the UE fails to report the event within the required delay, then a failure is recorded. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
7) After 6 seconds from the beginning of T2, the SS shall switch the power settings from T2 to T3.
8) UE shall transmit a MEASUREMENT REPORT message triggered by event 1G for cell 3. The measurement reporting delay from the beginning of T3 shall be less than 840 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
9) After 6 seconds from the beginning of T3, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
10) Repeat steps 1-9 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
TRUE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
1
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps TDD
-CHOICE Sync case
2
-Timeslot
0
-Cell parameters ID
0
-SCTD indicator
FALSE
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: Reporting interval = 0 ms means no periodical reporting
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1G
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps TDD
-CHOICE Sync case
Not present
-Cell parameters ID
Set to Cell parameters ID of Cell 2
-SCTD indicator
FALSE
MEASUREMENT REPORT message (step 8)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of Cell 3
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1G
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps TDD
-CHOICE Sync case
Not Present
-Cell parameters ID
Set to Cell parameters ID of Cell 3
-SCTD indicator
FALSE |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.5.1 3,84 Mcps TDD Option | The UE shall send one Event 1G triggered measurement report for Cell 2 with a measurement reporting delay less than 240ms from the beginning of time period T2.
The UE shall send one Event 1G triggered measurement report for Cell 3 with a measurement reporting delay less than 840ms from the beginning of time period T3.
The UE shall not send event triggered measurement reports, as long as the reporting criteria are not fulfilled.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of [FFS]% of the cases. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.5.2 1,28 Mcps TDD Option | The UE shall send one Event 1G triggered measurement report for Cell 2 with a measurement reporting delay less than 280ms from the beginning of time period T2.
The UE shall send one Event 1G triggered measurement report for Cell 3 with a measurement reporting delay less than 880ms from the beginning of time period T3.
The UE shall not send any incorrect event triggered measurement reports, as long as the reporting criteria are not fulfilled.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.1.5.3 7,68 Mcps TDD Option | The UE shall send one Event 1G triggered measurement report for Cell 2 with a measurement reporting delay less than 240ms from the beginning of time period T2.
The UE shall send one Event 1G triggered measurement report for Cell 3 with a measurement reporting delay less than 840ms from the beginning of time period T3.
The UE shall not send event triggered measurement reports, as long as the reporting criteria are not fulfilled.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2 Event 1H and 1I triggered reporting in AWGN propagation condition | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.1.1 3,84 Mcps TDD Option | In the event triggered reporting, the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This measurement reporting delay excludes a delay uncertainty resulted when inserting the measurement report to the TTI of the uplink DCCH. The delay uncertainty is twice the TTI of the uplink DCCH.
The requirements and this test apply to the TDD (3,84 Mcps option) UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.1.2 1,28 Mcps TDD Option | The purpose of this test is to verify that the UE makes correct reporting of events 1H (timeslot ISCP below threshold) and 1I (timeslot ISCP above threshold). This test will partly verify the requirements in [2]
The requirements and this test apply to all types of 1.28 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.1.3 7,68 Mcps TDD Option | In the event triggered reporting, the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This measurement reporting delay excludes a delay uncertainty resulted when inserting the measurement report to the TTI of the uplink DCCH. The delay uncertainty is twice the TTI of the uplink DCCH.
The requirements and this test apply to the TDD (7,68 Mcps option) UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.2.1 3,84 Mcps TDD Option | In CELL_DCH state the measurement period for intra frequency Timeslot ISCP measurements on arbitrary DL timeslots, including Beacon timeslots is 400 ms. When no inter frequency measurement is scheduled, the UE shall be capable of performing Timeslot ISCP measurements for a total of 10 different combinations of an arbitrary DL timeslot and an intra-frequency cell, including the current serving cell.
The normative reference for this requirement is TS 25.123 [2] clauses 8.1.2.2.2.A and A.8.1.2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.2.2 1,28 Mcps TDD Option | The UE shall send one event 1I triggered measurement report, with a measurement reporting delay less than 400 ms from the beginning of time period T2 as defined in the test method below.
The UE shall send one event 1H triggered measurement report, with a measurement reporting delay less than 400 ms from the beginning of time period T3 as defined in the test method below.
The UE shall send one event 1H triggered measurement report, with a measurement reporting delay less than 400 ms from the beginning of time period T4 as defined in the test method below. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.2.3 7,68 Mcps TDD Option | In CELL_DCH state the measurement period for intra frequency Timeslot ISCP measurements on arbitrary DL timeslots, including Beacon timeslots is 400 ms. When no inter frequency measurement is scheduled, the UE shall be capable of performing Timeslot ISCP measurements for a total of 10 different combinations of an arbitrary DL timeslot and an intra-frequency cell, including the current serving cell.
The normative reference for this requirement is TS 25.123 [2] clauses 8.1B.2.2.3 and A.8.1.2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.3 Test purpose | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.3.1 3,84 Mcps TDD Option | To verify that the UE meets the minimum requirement. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.3.2 1,28 Mcps TDD Option | To verify that the UE meets the minimum requirements. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.3.3 7,68 Mcps TDD Option | To verify that the UE meets the minimum requirements. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.4.1 3,84 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.4.1.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Tables 8.6.1.2.1, 8.6.1.2.2 and 8.6.1.2.3. The test consists of five successive time periods, with a time duration of T1, T2, T3, T4 and T5 respectively. Two cells shall be present in the test, cell 1 being the current serving cell and cell 2 being a neighbour cell on the used frequency.
In the measurement control information it shall be indicated to the UE that event-triggered reporting with event 1H and event 1I shall be used and that Timeslot ISCP and P-CCPCH RSCP shall be reported together with event 1H and 1I. Measurement control information shall be sent to the UE before the beginning of time period T1.
The second Beacon timeslot shall be provided in timeslot 8 for both cell 1 and cell 2. The UL DPCH shall be transmitted in timeslot 10. In addition, timeslots 3 and 4 shall be allocated as DL timeslots. Cell 1 and cell 2 shall be synchronised, i.e. share the same frame and timeslot timing.
Table 8.6.1.2.1: General test parameters for correct event 1H and event 1I reporting in AWGN propagation condition
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 1
HCS
Not used
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Timeslot list cell 1
2, 3, 4
Timeslot numbers in IE "Cell info" for Cell 1
Timeslot list cell 2
4
Timeslot numbers in IE "Cell info" for Cell 2
Threshold used frequency
dBm
-68
Threshold 1 applicable for event 1H, cell 1 timeslots 2, 4 and cell 2 timeslot 4
Threshold used frequency
dBm
-73
Threshold 2 applicable for event 1H, cell 1 timeslots 2, 3, 4 and cell 2 timeslot 4
Threshold used frequency
dBm
-67
Applicable for event 1I, cell 1 timeslots 2, 4 and cell 2 timeslot 4
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
Cell 2 shall belong to the monitored set
T1
s
5
T2
s
5
T3
s
5
T4
s
5
T5
s
5
Table 8.6.1.2.2: Cell 1 specific parameters for correct event 1H and 1I reporting in AWGN propagation condition
Parameter
Unit
Cell 1
T1
T2
T3
T4
T5
T1
T2
T3
T4
T5
UTRA RF Channel Number
Channel 1
DL timeslot number
0
2
PCCPCH_Ec/Ior
dB
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
SCH_toffset
dB
5
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
OCNS_Ec/Ior
dB
-3,12
Note 2
dB
4
4
PCCPCH RSCP
dBm
-69
n.a.
dBm / 3,84 MHz
-70
Propagation Condition
AWGN
DL timeslot number
3
4
PCCPCH_Ec/Ior
dB
n.a.
n.a.
SCH_Ec/Ior
dB
n.a.
n.a.
SCH_toffset
dB
n.a.
n.a.
DPCH_Ec/Ior
dB
n.a.
n.a.
OCNS_Ec/Ior
dB
0
0
dB
3
0
6
PCCPCH RSCP
dBm
n.a.
n.a.
dBm / 3,84 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior
Table 8.6.1.2.3: Cell 2 specific parameters for correct event 1H and 1I reporting in AWGN propagation condition
Parameter
Unit
Cell 2
T1
T2
T3
T4
T5
T1
T2
T3
T4
T5
UTRA RF Channel Number
Channel 1
DL timeslot number
0
2
PCCPCH_Ec/Ior
dB
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
SCH_toffset
dB
10
n.a.
DPCH_Ec/Ior
dB
n.a.
n.a.
OCNS_Ec/Ior
dB
-3,12
0
dB
1
0
6
0
PCCPCH RSCP
dBm
-72
n.a.
dBm / 3,84 MHz
-70
Propagation Condition
AWGN
DL timeslot number
3
4
PCCPCH_Ec/Ior
dB
n.a.
n.a.
SCH_Ec/Ior
dB
n.a.
n.a.
SCH_toffset
dB
n.a.
n.a.
DPCH_Ec/Ior
dB
n.a.
n.a.
OCNS_Ec/Ior
dB
0
0
dB
3
6
0
PCCPCH RSCP
dBm
n.a.
n.a.
dBm / 3,84 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.4.1.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds from the beginning of T1, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1I for cell 1 in timeslot 2. The measurement reporting delay from the beginning of T2 shall be less than 480 ms. If the UE fails to report the event within the required delay, then a failure is recorded. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
7) After 5 seconds from the beginning of T2, the SS shall switch the power settings from T2 to T3.
8) UE shall transmit a MEASUREMENT REPORT message triggered by event 1H for cell 1 in timeslot 2. The measurement reporting delay from the beginning of T3 shall be less than 480 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
9) After 5 seconds from the beginning of T3, the SS shall switch the power settings from T3 to T4.
10) UE shall transmit a MEASUREMENT REPORT message triggered by event 1H for cell 1 in timeslot 4. The measurement reporting delay from the beginning of T3 shall be less than 480 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
11) After 5 seconds from the beginning of T4, the SS shall switch the power settings from T4 to T5.
12) UE shall transmit a MEASUREMENT REPORT message triggered by event 1I for cell 2 in timeslot 4. The measurement reporting delay from the beginning of T3 shall be less than 480 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
13) After 5 seconds from the beginning of T5, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
14) Repeat steps 1-13 [TBD] times.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Timeslot ISCP
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
FALSE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
1
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
2
-Intra-frequency event identity
Event 1H
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
-68
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
-Intra-frequency event identity
Event 1H
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
-73
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
-Intra-frequency event identity
Event 1I
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
-67
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: Reporting interval = 0 ms means no periodical reporting
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
4
-Timeslot ISCP
Checked that this IE is present for 4 timeslots
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1I
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
MEASUREMENT REPORT message (step 8)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
4
-Timeslot ISCP
Checked that this IE is present for 4 timeslots
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1H
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
MEASUREMENT REPORT message (step 10)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
4
-Timeslot ISCP
Checked that this IE is present for 4 timeslots
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1H
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
MEASUREMENT REPORT message (step 12)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
1
-Timeslot ISCP
Checked that this IE is present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1I
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.4.2 1,28 Mcps TDD Option | Test environment : normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested : mid range ;see clauses G.2.4.
The test parameters are given in Table 8.6.1.2.4.2A, Table 8.6.1.2.4.2B and Table 8.6.1.2.4.2C below. The test consists of four successive time periods, with a time duration of T1, T2, T3 and T4 respectively. Two cells shall be present in the test, cell 1 being the current serving cell and cell 2 being a neighbour cell on the used frequency.
In the measurement control information it shall be indicated to the UE that event-triggered reporting with event 1H and event 1I shall be used and that Timeslot ISCP and P-CCPCH RSCP shall be reported together with event 1H and 1I. Measurement control information shall be sent to the UE before the beginning of time period T1.
The UL DPCH shall be transmitted in timeslot 2. In addition, timeslots 5 and 6 shall be allocated as DL timeslots.
Table 8.6.1.2.4.2A: General test parameters for correct event 1H and 1I reporting in AWGN propagation condition 1,28Mcps option
Parameter
Unit
Value
Comment
DCH parameters active cell
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 1
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Timeslot list cell 1
5, 6
Timeslot numbers in IE "Cell info" for Cell 1
Timeslot list cell 2
6
Timeslot numbers in IE "Cell info" for Cell 2
Threshold used frequency
dBm
-68
Applicable for event 1H, cell 1 timeslots 5, 6 and cell 2 timeslot 6
Threshold used frequency
dBm
-66
Applicable for event 1I, cell 1 timeslots 5, 6 and cell 2 timeslot 6
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
Cell 2 shall belong to the monitored set
T1
s
5
T2
s
5
T3
s
5
T4
s
5
Table 8.6.1.2.4.2B: Cell 1 specific test parameters for correct event 1H and 1I reporting in AWGN propagation condition 1,28Mcps Option
Parameter
Unit
Cell 1
T1
T2
T3
T4
T1
T2
T3
T4
T1
T2
T3
T4
UTRA RF Channel Number
Channel 1
DL timeslot number
0
5
6
PCCPCH_Ec/Ior
dB
-3
DPCH_Ec/Ior
dB
Note 1
OCNS_Ec/Ior
dB
-3
Note 2
0
dB
4
3
4
20
4
PCCPCH RSCP
dBm
-79
n.a.
n.a.
ISCP
dBm
Note 3
Note 3
-60
-60
-74.54
-74.54
dBm / 1,28 MHz
-80
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior
Note 3: ISCP of TS0 and TS5 remains changeless.
Table 8.6.1.2.4.2C: Cell 2 specific test parameters for correct event 1H and 1I reporting in AWGN propagation condition 1,28Mcps option
Parameter
Unit
Cell 2
T1
T2
T3
T4
T1
T2
T3
T4
UTRA RF Channel Number
Channel 1
DL timeslot number
0
6
PCCPCH_Ec/Ior
dB
-3
DPCH_Ec/Ior
dB
OCNS_Ec/Ior
dB
-3
0
dB
4
20
4
PCCPCH RSCP
dBm
-79
n.a.
ISCP
dBm
Note1
-74.54
-60
-60
-74.54
dBm / 1,28 MHz
-80
Note1: ISCP of TS0 remains changeless
Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds from the beginning of T1, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1I for cell 2 in timeslot 6. The measurement reporting delay from the beginning of T2 shall be less than 480 ms. If the UE fails to report the event within the required delay, then a failure is recorded. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
7) After 5 seconds from the beginning of T2, the SS shall switch the power settings from T2 to T3.
8) UE shall transmit a MEASUREMENT REPORT message triggered by event 1H for cell 1 in timeslot 6 . The measurement reporting delay from the beginning of T3 shall be less than 480 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
9) After 5 seconds from the beginning of T3, the SS shall switch the power settings from T3 to T4.
10) UE shall transmit a MEASUREMENT REPORT message triggered by event 1H for cell 2 in timeslot 6. The measurement reporting delay from the beginning of T3 shall be less than 480 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
11) After 5 seconds from the beginning of T4, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
12) Repeat steps 1-13 [TBD] times.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3], with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Timeslot ISCP
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
FALSE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
1
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
2
-Intra-frequency event identity
Event 1H
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
-68
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
-Intra-frequency event identity
Event 1I
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
-66
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: Reporting interval = 0 ms means no periodical reporting
MEASUREMENT REPORT message (step 6)
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
6
-Timeslot ISCP
Checked that this IE is present for 4 timeslots
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1I
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 2
MEASUREMENT REPORT message (step 8)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
6
-Timeslot ISCP
Checked that this IE is present for 4 timeslots
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1H
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
MEASUREMENT REPORT message (step 10)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
6
-Timeslot ISCP
Checked that this IE is present for 4 timeslots
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1H
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 2 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.4.3 7,68 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.4.3.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Tables 8.6.1.2.4.3.1.1, 8.6.1.2.4.3.1.2 and 8.6.1.2.4.3.1.3. The test consists of five successive time periods, with a time duration of T1, T2, T3, T4 and T5 respectively. Two cells shall be present in the test, cell 1 being the current serving cell and cell 2 being a neighbour cell on the used frequency.
In the measurement control information it shall be indicated to the UE that event-triggered reporting with event 1H and event 1I shall be used and that Timeslot ISCP and P-CCPCH RSCP shall be reported together with event 1H and 1I. Measurement control information shall be sent to the UE before the beginning of time period T1.
The second Beacon timeslot shall be provided in timeslot 8 for both cell 1 and cell 2. The UL DPCH shall be transmitted in timeslot 10. In addition, timeslots 3 and 4 shall be allocated as DL timeslots. Cell 1 and cell 2 shall be synchronised, i.e. share the same frame and timeslot timing.
Table 8.6.1.2.4.3.1.1: General test parameters for correct event 1H and event 1I reporting in AWGN propagation condition
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 1
HCS
Not used
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Timeslot list cell 1
2, 3, 4
Timeslot numbers in IE "Cell info" for Cell 1
Timeslot list cell 2
4
Timeslot numbers in IE "Cell info" for Cell 2
Threshold used frequency
dBm
-68
Threshold 1 applicable for event 1H, cell 1 timeslots 2, 4 and cell 2 timeslot 4
Threshold used frequency
dBm
-73
Threshold 2 applicable for event 1H, cell 1 timeslots 2, 3, 4 and cell 2 timeslot 4
Threshold used frequency
dBm
-67
Applicable for event 1I, cell 1 timeslots 2, 4 and cell 2 timeslot 4
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
Cell 2 shall belong to the monitored set
T1
s
5
T2
s
5
T3
s
5
T4
s
5
T5
s
5
Table 8.6.1.2.4.3.1.2: Cell 1 specific parameters for correct event 1H and 1I reporting in AWGN propagation condition
Parameter
Unit
Cell 1
T1
T2
T3
T4
T5
T1
T2
T3
T4
T5
UTRA RF Channel Number
Channel 1
DL timeslot number
0
2
PCCPCH_Ec/Ior
dB
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
SCH_toffset
dB
5
n.a.
DPCH_Ec/Ior
dB
n.a.
Note 1
OCNS_Ec/Ior
dB
-3,12
Note 2
dB
4
4
PCCPCH RSCP
dBm
-69
n.a.
dBm / 7,68 MHz
-70
Propagation Condition
AWGN
DL timeslot number
3
4
PCCPCH_Ec/Ior
dB
n.a.
n.a.
SCH_Ec/Ior
dB
n.a.
n.a.
SCH_toffset
dB
n.a.
n.a.
DPCH_Ec/Ior
dB
n.a.
n.a.
OCNS_Ec/Ior
dB
0
0
dB
3
0
6
PCCPCH RSCP
dBm
n.a.
n.a.
dBm / 7,68 MHz
-70
Propagation Condition
AWGN
Note 1: The DPCH level is controlled by the power control loop
Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior
Table 8.6.1.2.4.3.1.3: Cell 2 specific parameters for correct event 1H and 1I reporting in AWGN propagation condition
Parameter
Unit
Cell 2
T1
T2
T3
T4
T5
T1
T2
T3
T4
T5
UTRA RF Channel Number
Channel 1
DL timeslot number
0
2
PCCPCH_Ec/Ior
dB
-3
n.a.
SCH_Ec/Ior
dB
-9
n.a.
SCH_toffset
dB
10
n.a.
DPCH_Ec/Ior
dB
n.a.
n.a.
OCNS_Ec/Ior
dB
-3,12
0
dB
1
0
6
0
PCCPCH RSCP
dBm
-72
n.a.
dBm / 7,68 MHz
-70
Propagation Condition
AWGN
DL timeslot number
3
4
PCCPCH_Ec/Ior
dB
n.a.
n.a.
SCH_Ec/Ior
dB
n.a.
n.a.
SCH_toffset
dB
n.a.
n.a.
DPCH_Ec/Ior
dB
n.a.
n.a.
OCNS_Ec/Ior
dB
0
0
dB
3
6
0
PCCPCH RSCP
dBm
n.a.
n.a.
dBm / 7,68 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.4.3.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 5 seconds from the beginning of T1, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 1I for cell 1 in timeslot 2. The measurement reporting delay from the beginning of T2 shall be less than 480 ms. If the UE fails to report the event within the required delay, then a failure is recorded. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
7) After 5 seconds from the beginning of T2, the SS shall switch the power settings from T2 to T3.
8) UE shall transmit a MEASUREMENT REPORT message triggered by event 1H for cell 1 in timeslot 2. The measurement reporting delay from the beginning of T3 shall be less than 480 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
9) After 5 seconds from the beginning of T3, the SS shall switch the power settings from T3 to T4.
10) UE shall transmit a MEASUREMENT REPORT message triggered by event 1H for cell 1 in timeslot 4. The measurement reporting delay from the beginning of T3 shall be less than 480 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
11) After 5 seconds from the beginning of T4, the SS shall switch the power settings from T4 to T5.
12) UE shall transmit a MEASUREMENT REPORT message triggered by event 1I for cell 2 in timeslot 4. The measurement reporting delay from the beginning of T3 shall be less than 480 ms. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
13) After 5 seconds from the beginning of T5, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
14) Repeat steps 1-13 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Timeslot ISCP
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
FALSE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
TRUE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
TRUE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
1
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
2
-Intra-frequency event identity
Event 1H
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
-68
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
-Intra-frequency event identity
Event 1H
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
-73
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
-Intra-frequency event identity
Event 1I
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
-67
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: Reporting interval = 0 ms means no periodical reporting
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
4
-Timeslot ISCP
Checked that this IE is present for 4 timeslots
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1I
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps TDD
-CHOICE Sync case
Not Present
-Cell parameters ID
Set to Cell parameters ID of Cell 1
-SCTD indicator
FALSE
MEASUREMENT REPORT message (step 8)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
4
-Timeslot ISCP
Checked that this IE is present for 4 timeslots
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1H
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps TDD
-CHOICE Sync case
Not Present
-Cell parameters ID
Set to Cell parameters ID of Cell 1
-SCTD indicator
FALSE
MEASUREMENT REPORT message (step 10)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 1
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
4
-Timeslot ISCP
Checked that this IE is present for 4 timeslots
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1H
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps TDD
-CHOICE Sync case
Not Present
-Cell parameters ID
Set to Cell parameters ID of Cell 1
-SCTD indicator
FALSE
MEASUREMENT REPORT message (step 12)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Intra-frequency Measured results list
-Intra-frequency measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to Cell parameters ID of cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
1
-Timeslot ISCP
Checked that this IE is present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Intra-frequency measurement event results
-Intra-frequency event identity
1I
-Cell measurement event results (10.3.7.4)
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
7,68 Mcps TDD
-CHOICE Sync case
Not Present
-Cell parameters ID
Set to Cell parameters ID of Cell 2
-SCTD indicator
FALSE |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.5 Test requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.5.1 3,84 Mcps TDD Option | The UE shall send one event 1I triggered measurement report, with a measurement reporting delay less than 480 ms from the beginning of time period T2.
The UE shall send one event 1H triggered measurement report, with a measurement reporting delay less than 480 ms from the beginning of time period T3.
The UE shall send one event 1H triggered measurement report, with a measurement reporting delay less than 480 ms from the beginning of time period T4.
The UE shall send one event 1I triggered measurement report, with a measurement reporting delay less than 480 ms from the beginning of time period T5.
The UE shall not send event 1H or 1I triggered measurement reports, as long as the reporting criteria are not fulfilled.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of [FFS]% of the cases. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.5.2 1,28 Mcps TDD Option | The UE shall not send event 1H or 1I triggered measurement reports, as long as the reporting criteria are not fulfilled.
The rate of correct events observed during repeated tests shall be at least 90%. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.2.5.3 7,68 Mcps TDD Option | The UE shall send one event 1I triggered measurement report, with a measurement reporting delay less than 480 ms from the beginning of time period T2.
The UE shall send one event 1H triggered measurement report, with a measurement reporting delay less than 480 ms from the beginning of time period T3.
The UE shall send one event 1H triggered measurement report, with a measurement reporting delay less than 480 ms from the beginning of time period T4.
The UE shall send one event 1I triggered measurement report, with a measurement reporting delay less than 480 ms from the beginning of time period T5.
The UE shall not send event 1H or 1I triggered measurement reports, as long as the reporting criteria are not fulfilled.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3 Correct reporting of neighbours in fading propagation conditions | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.1 3,84 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.1.1 Definition and applicability | In the event triggered reporting, the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This measurement reporting delay excludes a delay uncertainty resulted when inserting the measurement report to the TTI of the uplink DCCH. The delay uncertainty is twice the TTI of the uplink DCCH.
The requirements and this test apply to the TDD (3,84 Mcps option) UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.1.2 Minimum requirement | The requirements are the same as in sub clause 8.6.1.1.2
The normative reference for this requirement is TS 25.123 [2] clauses 8.1.2.2.2.1, 8.1.2.2.2 and A.8.1.3 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.1.3 Test purpose | To verify that the UE meets the minimum requirements and also verify that the UE performs sufficient layer 1 filtering of the measurements. The test is performed in fading propagation conditions. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.1.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Tables 8.6.1.3.1 and 8.6.1.3.2. The test consists of one time period with time duration of T1. Two cells shall be present in the test, cell 1 being the current serving cell and cell 2 being a neighbour cell on the used frequency. Cell 1 and cell 2 shall be synchronised, i.e. share the same frame and timeslot timing.
In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP shall be reported together with Event 1G.
The DL DPCH shall be transmitted in timeslot 4 and the UL DPCH shall be transmitted in timeslot 12. The TTI of the UL DCCH shall be 20ms.
Table 8.6.1.3.1: General test parameters for correct reporting of neighbours in fading propagation condition
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 1
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
200
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
Sent before the beginning of time period T1
T1
s
200
Table 8.6.1.3.2: Cell specific test parameters for correct reporting of neighbours in fading propagation condition
Parameter
Unit
Cell 1
Cell 2
T1
T1
T1
T1
DL timeslot number
0
8
0
8
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
-3
n.a.
SCH_Ec/Ior
dB
-9
-9
-9
-9
SCH_toffset
0
0
2
2
PICH_Ec/Ior
dB
n.a.
-3
n.a.
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
dB
7
7
2
2
PCCPCH RSCP
dBm
-66
n.a.
-71
n.a.
dBm/ 3,84 MHz
-70
Propagation Condition
Case 4 as specified in Annex DTS25.102 Annex B |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.1.4.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 200 seconds from the beginning of T1, the UE is switched off.
6) Repeat steps 1-5 [TBD] times.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
FALSE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
FALSE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
1
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: Reporting interval = 0 ms means no periodical reporting |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.1.5 Test requirements | The number of Event 1G triggered measurement reports during time period T1 shall be less than 60.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of [FFS]% of the cases. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.2 1,28 Mcps TDD Option | Void. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.3 7,68 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.3.1 Definition and applicability | In the event triggered reporting, the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This measurement reporting delay excludes a delay uncertainty resulted when inserting the measurement report to the TTI of the uplink DCCH. The delay uncertainty is twice the TTI of the uplink DCCH.
The requirements and this test apply to the TDD (7,68 Mcps option) UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.3.2 Minimum requirement | The requirements are the same as in sub clause 8.6.1.1.2
The normative reference for this requirement is TS 25.123 [2] clauses , 8.1B.2.2.2 and A.8.1.3.3 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.3.3 Test purpose | To verify that the UE meets the minimum requirements and also verify that the UE performs sufficient layer 1 filtering of the measurements. The test is performed in fading propagation conditions. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.3.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.3.4.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Tables 8.6.1.3.3.4.1.1 and 8.6.1.3.3.4.1.2. The test consists of one time period with time duration of T1. Two cells shall be present in the test, cell 1 being the current serving cell and cell 2 being a neighbour cell on the used frequency. Cell 1 and cell 2 shall be synchronised, i.e. share the same frame and timeslot timing.
In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP shall be reported together with Event 1G.
The DL DPCH shall be transmitted in timeslot 4 and the UL DPCH shall be transmitted in timeslot 12. The TTI of the UL DCCH shall be 20ms.
Table 8.6.1.3.3.4.1.1: General test parameters for correct reporting of neighbours in fading propagation condition
Parameter
Unit
Value
Comment
DCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
Neighbour cell
Cell 2
Final condition
Active cell
Cell 1
O
dB
0
Cell individual offset. This value shall be used for all cells in the test.
Hysteresis
dB
0
Time to Trigger
ms
200
Filter coefficient
0
Monitored cell list size
6 TDD neighbours on Channel 1
Sent before the beginning of time period T1
T1
s
200
Table 8.6.1.3.3.4.1.2: Cell specific test parameters for correct reporting of neighbours in fading propagation condition
Parameter
Unit
Cell 1
Cell 2
T1
T1
T1
T1
DL timeslot number
0
8
0
8
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
n.a.
-3
n.a.
SCH_Ec/Ior
dB
-9
-9
-9
-9
SCH_toffset
0
0
2
2
PICH_Ec/Ior
dB
n.a.
-3
n.a.
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
dB
7
7
2
2
PCCPCH RSCP
dBm
-66
n.a.
-71
n.a.
dBm/ 7,68 MHz
-70
Propagation Condition
Case 4 as specified in TS25.102 Annex B |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.3.4.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 200 seconds from the beginning of T1, the UE is switched off.
6) Repeat steps 1-5 until the confidence level according to annex F.6.2 is achieved..
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Intra-frequency measurement
-Intra-frequency measurement (10.3.7.36)
-Intra-frequency measurement objects list (10.3.7.33)
Not Present
-Intra-frequency measurement quantity (10.3.7.38)
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity list
1
-Measurement quantity
Primary CCPCH
-Intra-frequency reporting quantity (10.3.7.41)
-Reporting quantities for active set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
FALSE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for monitored set cells (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell Identity reporting indicator
FALSE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting quantities for detected set cells (10.3.7.5)
Not Present
-Reporting cell status (10.3.7.61)
-CHOICE reported cell
Report all active set cells + cells within monitored set on used frequency
-Maximum number of reported cells
1
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Intra-frequency measurement reporting criteria
-Intra-frequency measurement reporting criteria (10.3.7.39)
-Parameters required for each event
1
-Intra-frequency event identity
Event 1G
-Triggering condition 2
Not Present
-Reporting Range Constant
Not Present
-Cells forbidden to affect Reporting Range
Not Present
-W
Not Present
-Hysteresis
0 dB
-Threshold used frequency
Not Present
-Reporting deactivation threshold
Not Present
-Replacement activation threshold
Not Present
-Time to trigger
0 ms
-Amount of reporting
Infinity
-Reporting interval
0 ms (Note 1)
-Reporting cell status
Not Present
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
Note 1: Reporting interval = 0 ms means no periodical reporting |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.1.3.3.5 Test requirements | The number of Event 1G triggered measurement reports during time period T1 shall be less than 60.
For the test to pass, the total number of successful tests shall be more than 90% with a confidence level of 95% of the cases. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2 TDD inter frequency measurements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1 Correct reporting of neighbours in AWGN propagation condition | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.1.1 3,84 Mcps TDD Option | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This measurement reporting delay excludes a delay uncertainty resulted when inserting the measurement report to the TTI of the uplink DCCH. The delay uncertainty is twice the TTI of the uplink DCCH.
The requirements and this test apply to the TDD (3,84 Mcps option) UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.1.2 1,28 Mcps TDD Option | The purpose of this test is to verify that the UE makes correct reporting of an event within the required times when doing inter frequency measurements on a neighbouring TDD cell. The test will partly verify the requirements in section 8.1A.2 and 9.1. of [2]. The requirements and this test apply to the TDD (1.28 Mcps option) UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.1.3 7,68 Mcps TDD Option | In the event triggered reporting period the measurement reporting delay is defined as the time between any event that will trigger a measurement report until the UE starts to transmit over the Uu interface. This requirement assumes that the measurement report is not delayed by other RRC signalling on the DCCH. This measurement reporting delay excludes a delay uncertainty resulted when inserting the measurement report to the TTI of the uplink DCCH. The delay uncertainty is twice the TTI of the uplink DCCH.
The requirements and this test apply to the TDD (7,68 Mcps option) UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.2.1 3,84 Mcps TDD Option | When idle intervals are used for inter-frequency TDD measurements, the UE shall be able to identify a new detectable inter-frequency TDD cell belonging to the monitored set within
If the UE does not require idle intervals to perform inter-frequency TDD measurements, the UE shall be able to identify a new detectable inter-frequency TDD cell belonging to the monitored set within 5000 ms.
When idle intervals are used for TDD inter frequency measurements, the UE shall be capable of performing P-CCPCH RSCP measurements for Xmeasurement TDD inter inter-frequency TDD cells per TDD frequency of the monitored set.
The UE physical layer shall be capable of reporting measurements to higher layers with measurement accuracy as specified in section 9 and with a measurement period of Tmeasurement inter.
If the UE does not require idle intervals to perform TDD inter-frequency measurements, the measurement period for inter frequency P-CCPCH RSCP measurements shall be 480 ms.
Where,
Xmeasurement TDD inter = 6 (cells)
Tmeasurement_period inter = 480 ms. The time period used for calculating the measurement period Tmeasurement_inter for inter frequency P-CCPCH RSCP measurements.
NTDD inter: This is the available number of measurement opportunities for a Beacon timeslot of an inter-frequency TDD cell during the time period TTDD inter. The UE shall consider that a measurement opportunity on a Beacon timeslot of an inter-frequency TDD cell is provided if an idle interval of length equal to or greater than 3 timeslots less 2*0.5 ms implementation margin for frequency switching per idle interval completely overlaps in time with the Beacon timeslot of the inter-frequency TDD cell.
Nbasic_identify_TDD inter = 80. This is a number of measurement opportunities for a Beacon timeslot of an inter-frequency TDD cell during the time period used in the inter frequency TDD equation where the maximum allowed time for the UE to identify a new detectable inter-frequency TDD cell is defined.
Nbasic_measurement_TDD inter = 5. This is a number of measurement opportunities for a Beacon timeslot of an inter-frequency TDD cell during the time period TTDD inter used in the inter-frequency TDD equation where the measurement period for inter-frequency P-CCPCH RSCP measurements is defined.
NFreq TDD: This is the number of TDD frequencies indicated in the inter frequency measurement control information.
The event triggered measurement reporting delay, measured without L3 filtering shall be less than T identify inter defined in 25.123 [2]. When L3 filtering is used, an additional delay can be expected.
The normative reference for this requirement is TS 25.123 [2] clauses 8.1.2.3.1, 8.1.2.3.2 and A.8.2.1 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.2.2 1,28 Mcps TDD Option | When idle intervals are used for inter-frequency TDD measurements, the UE shall be able to identify a new detectable cell belonging to the monitored set within
when
NInter: This is the minimum number of sub-frame in that the signal of P-CCPCH and DwPCH can be received for inter frequency target cell during the period TMeasurement_Period inter with an arbitrarily chosen timing. It depends on the channel allocation and is calculated by assuming 2*0.1ms for implementation margin (for the description of the idle intervals see Annex A of 25.225).
Tbasic_identify_TDD,inter= 800ms. This is the time period used in the inter frequency equation where the maximum allowed time for the UE to identify a new TDD cell is defined.
TMeasurement_Period Inter= 480 ms. The period used for calculating the measurement period Tmeasurement_inter for inter frequency P-CCPCH RSCP measurements.
NFreq: Number of TDD frequencies indicated in the inter frequency measurement control information.
If the UE does not require idle intervals to perform inter-frequency TDD measurements, the UE shall be able to identify a new detectable inter-frequency TDD cell belonging to the monitored set within 5000 ms.
A cell shall be considered detectable when P-CCPCH Ec/Io > -8 dB and DwPCH_Ec/Io > -5 dB. When L3 filtering is used an additional delay can be expected.
The test consist of 2 successive time periods, with a time duration T1 and T2. The test parameters are given in tables A.8.2C and A.8.2D below. Two cells shall be present in the test, cell 1 being the active cell and cell 2 being a 1.28Mcps TDD option neighbour cell on the unused frequency.
In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. P-CCPCH RSCP of the best cell on the unused frequency shall be reported together with Event 2C reporting. The measurement control message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T1 is at least equal to the RRC procedure delay as defined in 25.331 [9] |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.2.3 7,68 Mcps TDD Option | When idle intervals are used for inter-frequency TDD measurements, the UE shall be able to identify a new detectable inter-frequency TDD cell belonging to the monitored set within
If the UE does not require idle intervals to perform inter-frequency TDD measurements, the UE shall be able to identify a new detectable inter-frequency TDD cell belonging to the monitored set within 5000 ms.
When idle intervals are used for TDD inter frequency measurements, the UE shall be capable of performing P-CCPCH RSCP measurements for Xmeasurement TDD inter inter-frequency TDD cells per TDD frequency of the monitored set.
The UE physical layer shall be capable of reporting measurements to higher layers with measurement accuracy as specified in section 9 and with a measurement period of Tmeasurement inter.
If the UE does not require idle intervals to perform TDD inter-frequency measurements, the measurement period for inter frequency P-CCPCH RSCP measurements shall be 480 ms.
Where,
Xmeasurement TDD inter = 6 (cells)
Tmeasurement_period inter = 480 ms. The time period used for calculating the measurement period Tmeasurement_inter for inter frequency P-CCPCH RSCP measurements.
NTDD inter: This is the available number of measurement opportunities for a Beacon timeslot of an inter-frequency TDD cell during the time period TTDD inter. The UE shall consider that a measurement opportunity on a Beacon timeslot of an inter-frequency TDD cell is provided if an idle interval of length equal to or greater than 3 timeslots less 2*0.5 ms implementation margin for frequency switching per idle interval completely overlaps in time with the Beacon timeslot of the inter-frequency TDD cell.
Nbasic_identify_TDD inter = 80. This is a number of measurement opportunities for a Beacon timeslot of an inter-frequency TDD cell during the time period used in the inter frequency TDD equation where the maximum allowed time for the UE to identify a new detectable inter-frequency TDD cell is defined.
Nbasic_measurement_TDD inter = 5. This is a number of measurement opportunities for a Beacon timeslot of an inter-frequency TDD cell during the time period TTDD inter used in the inter-frequency TDD equation where the measurement period for inter-frequency P-CCPCH RSCP measurements is defined.
NFreq TDD: This is the number of TDD frequencies indicated in the inter frequency measurement control information.
The event triggered measurement reporting delay, measured without L3 filtering shall be less than T identify inter defined in 25.123 [2]. When L3 filtering is used, an additional delay can be expected.
The normative reference for this requirement is TS 25.123 [2] clauses 8.1B.2.3.1, 8.1B.2.3.2 and A.8.2.1 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.3 Test purpose | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.3.1 3,84 Mcps TDD Option | To verify that the UE meets the minimum requirement. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.3.2 1,28 Mcps TDD Option | To verify that the UE meets the minimum time requirements for identifying neighbouring TDD cells |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.3.3 7,68 Mcps TDD Option | To verify that the UE meets the minimum time requirements for identifying neighbouring interfrequency TDD cells. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.4.1 3,84 Mcps TDD Option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.4.1.1 Initial conditions | Test environment: normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested: mid range; see clause G.2.4.
The test parameters are given in Table 8.6.2.1.1 and 8.6.2.1.2. The test consists of 2 successive time periods, with a time duration T1 and T2. Two cells shall be present in the test, cell 1 being the serving cell and cell 2 being a UTRA TDD neighbour cell on the unused frequency. All cells shall be synchronised, i.e. share the same frame and timeslot timing.
In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. P-CCPCH RSCP of the best cell on the unused frequency shall be reported together with Event 2C reporting. The Measurement control message shall be sent to the UE such that the delay between the end of the last received TTI containing the message and the beginning of T1 is at least equal to the RRC procedure delay as defined in [9].
The second Beacon timeslot shall be provided in timeslot 8 for both cell 1 and cell 2. The DL DPCH shall be transmitted in timeslot 1 and the UL DPCH shall be transmitted in timeslot 3. The TTI of the uplink DCCH shall be 20 ms.
Table 8.6.2.1.1: General test parameters for Correct reporting of TDD inter-frequency neighbours in AWGN propagation condition (3,84 Mcps option)
Parameter
Unit
Value
Comment
DPCH parameters
DL Reference Measurement Channel 12.2 kbps
As specified in Annex CTS 25.102 annex A.2.2
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
UTRA TDD cell
Neighbour cell
Cell 2
UTRA TDD cell
Threshold non used frequency
dB
-71
Applicable for event 2C
Hysteresis
dB
0
Applicable for event 2C
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
24 on channel 1
16 on channel 2
T1
s
10
T2
s
10
Table 8.6.2.1.2: Cell specific parameters for Correct reporting of TDD inter-frequency neighbours in AWGN propagation condition (3,84 Mcps option)
Parameter
Unit
Cell 1
Cell 2
Timeslot Number
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
15
15
15
15
PICH_Ec/Ior
-3
-3
-3
-3
OCNS
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
dB
3
3
3
3
-Infinity
9
-Infinity
9
dBm/3,84 MHz
-70
PCCPCH_RSCP
dB
-70
-70
-Infinity
-64
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.4.1.2 Procedure | 1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 10 seconds from the beginning of T1, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2c for cell 2. The measurement reporting delay from the beginning of T2 shall be less than 5080 ms. If the UE fails to report the event within the required delay, then a failure is recorded. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
7) After 10 seconds from the beginning of T3, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
8) Repeat steps 1-7 [TBD] times.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] with the following exceptions:
NOTE: Numbers in brackets after an item e.g “Message Type (10.2.17)” in the IE description are references to clause numbers in TS 25.331 [9] describing that item in more detail.MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
-CHOICE inter-frequency cell removal
No inter-frequency cells removed
-New inter-frequency cells
1
-Inter-frequency cell id
1
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2
-Cell info (10.3.7.2)
-Cell individual offset
Not Present
-Reference time difference to cell
Not Present
-Read SFN indicator
False
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
3,84 Mcps TDD
-CHOICE Sync case
2
-Timeslot
0
-cell parameters ID
Set to cell parameters ID of cell 2
-SCTD indicator
FALSE
-Primary CCPCH Tx power
Set to Primary CCPCH Tx power of cell 2 as described in Table 8.6.2.1.2
-Timesllot list
Not Present
-Cell selection and re-selection info
Not Present
-Cell for measurement
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting critera
Inter-frequency reporting criteria
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA carrier RSSI
-Frequency quality estimate
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell identity reporting indicator
FALSE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN Reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting cell status (10.3.7.61)
Not Present
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Intra-frequency event identity
Event 2C
-Threshold used frequency
Not Present
-W Used frequency
Not Present
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting Cell Status (10.3..61)
-CHOICE reported cell
Report cells within active and/or monitored set on used frequency or within virtual active and/or monitored set on non-used frequency
-Maximum number of reported cells
3
-Parameters required for each non-used frequenc
- Threshold non-used frequency
-71
- W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Inter-frequency Measured results list
-Inter-frequency measured results
1
-Frequency info
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2
-UTRA carrier RSSI
Not Present
-Inter-frequency cell measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to cell parameters ID of Cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Inter-frequency measurement event results
-Inter-frequency event identity
2C
-Inter-frequency cells
1
-Frequency Info
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2
-CHOICE mode
TDD
-Primary CCPCH Info
-CHOICE mode
TDD
-CHOICE TDD Option
3,84 Mcps TDD
-CHOICE Sync Case
Not Present
-Cell Parameters ID
Set to cell parameters ID of Cell 2
-SCTD Indicator
FALSE |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.6.2.1.4.2 1,28 Mcps TDD Option | Test environment : normal; see clauses G.2.1 and G.2.2.
Frequencies to be tested : mid range ;see clauses G.2.4.
Cell 1 is the active cell, Cell 2 is a neighbour cell on the unused frequency. The power level on Cell 1 is kept constant and the power level of Cell 2 is changed using "change of best cell event". General test parameters are given in the table 8.6.2.1.3 below and they are signalled from test device. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. P-CCPCH RSCP of the best cell has to be reported together with Event 2C reporting. New measurement control information, which defines neighbour cells etc., is always sent before the event starts. The cell specific test parameters are shown in Table 8.6.2.1.4.
Table 8.6.2.1.3: General test parameters for correct reporting of TDD inter frequency neighbours in AWGN propagation condition 1,28Mcps option
Parameter
Unit
Value
Comment
DPCH parameters active cell
DL and UL Reference Measurement Channel 12.2 kbps
As specified in TS 25.102 section A.2.2. The DPCH is located in an other timeslot than 0
Power Control
On
Target quality value on DTCH
BLER
0.01
Initial conditions
Active cell
Cell 1
1.28Mcps TDD cell
Neighbour cell
Cell 2
1.28Mcps TDD cell
Final condtions
Active cell
Cell 1
Threshold non used frequency
dBm
-71
Absolute P-CCPCH RSCP threshold for event 2C
W non-used frequency
1
Applicable for event 2C
Hysteresis
dB
0
Time to Trigger
ms
0
Filter coefficient
0
Monitored cell list size
24 on channel 1
16 on channel 2
Measurement control information is sent before T1 starts.
T1
s
10
T2
s
10
Table 8.6.2.1.4 Cell Specific Parameters for Correct Reporting of Neighbours in AWGN Propagation Condition 1,28Mcps option
Parameter
Unit
Cell 1
Cell 2
Timeslot Number
0
DwPTS
0
DwPTS
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
DwPCH_Ec/Ior
dB
0
0
OCNS_Ec/Ior
dB
-3
-3
dB
3
3
-Infinity
8
dBm/1.28 MHz
-70
PCCPCH_RSCP
dBm
-70
-70
-Infinity
-65
Propagation Condition
AWGN
NOTE: The DPCH of all cells are located in a timeslot other than 0.
8.6.2.1.4.2.2 Test Procedure
1) The RF parameters are set up according to T1.
2) The UE is switched on.
3) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause 7.4.2 to place the UE in CELL_DCH.
4) SS shall transmit a MEASUREMENT CONTROL message.
5) After 10 seconds from the beginning of T1, the SS shall switch the power settings from T1 to T2.
6) UE shall transmit a MEASUREMENT REPORT message triggered by event 2c for cell 2. The measurement reporting delay from the beginning of T2 shall be less than 5080 ms. If the UE fails to report the event within the required delay, then a failure is recorded. If the reporting delay for this event is within the required limit, the number of succesfull tests is increased by one.
7) After 10 seconds from the beginning of T2, the UE is switched off. Any timing information of cell 2 is deleted in the UE.
8) Repeat steps 1-7 until the confidence level according to annex F.6.2 is achieved.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3] and in Annex A of 34.123-1 [21], with the following exceptions:
Note: Numbers in brackets after an item e.g “Message Type (10.2.17)” in the IE description are references to clause numbers in TS 25.331 [9] describing that item in more detail.
MEASUREMENT CONTROL message (step 4):
Information Element/Group name
Value/Remark
Message Type (10.2.17)
UE information elements
-RRC transaction identifier
0
-Integrity check info
Not Present
Measurement Information elements
-Measurement Identity
1
-Measurement Command (10.3.7.46)
Modify
-Measurement Reporting Mode (10.3.7.49)
-Measurement Report Transfer Mode
AM RLC
-Periodical Reporting / Event Trigger Reporting Mode
Event trigger
-Additional measurements list (10.3.7.1)
Not Present
-CHOICE Measurement type
Inter-frequency measurement
-Inter-frequency measurement (10.3.7.16)
-Inter-frequency measurement objects list (10.3.7.13)
-CHOICE inter-frequency cell removal
No inter-frequency cells removed
-New inter-frequency cells
1
-Inter-frequency cell id
1
-Frequency info (10.3.6.36)
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2
-Cell info (10.3.7.2)
-Cell individual offset
Not Present
-Reference time difference to cell
Not Present
-Read SFN indicator
False
-CHOICE mode
TDD
-Primary CCPCH info (10.3.6.57)
-CHOICE mode
TDD
-CHOICE TDD option
1,28 Mcps TDD
-cell parameters ID
Set to cell parameters ID of cell 2
-SCTD indicator
FALSE
-Primary CCPCH Tx power
Set to Primary CCPCH Tx power of cell 2 as described in Table 8.6.2.1.2
-Timesllot list
Not Present
-Cell selection and re-selection info
Not Present
-Cell for measurement
Not Present
-Inter-frequency measurement quantity (10.3.7.18)
-CHOICE reporting critera
Inter-frequency reporting criteria
-Filter coefficient (10.3.7.9)
0
-CHOICE mode
TDD
-Measurement quantity for frequency quality estimate
Primary CCPCH RSCP
-Inter-frequency reporting quantity (10.3.7.21)
-UTRA carrier RSSI
FALSE
-Frequency quality estimate
FALSE
-Non frequency related cell reporting quantities (10.3.7.5)
-SFN-SFN observed time difference reporting indicator
No report
-Cell synchronisation information reporting indicator
FALSE
-Cell identity reporting indicator
FALSE
-CHOICE mode
TDD
-Timeslot ISCP reporting indicator
FALSE
-Proposed TGSN Reporting required
FALSE
-Primary CCPCH RSCP reporting indicator
TRUE
-Pathloss reporting indicator
FALSE
-Reporting cell status (10.3.7.61)
Not Present
-Measurement validity (10.3.7.51)
Not Present
-CHOICE report criteria
Inter-frequency measurement reporting criteria
-Inter-frequency measurement reporting criteria (10.3.7.19)
-Parameters required for each event
1
-Intra-frequency event identity
Event 2C
-Threshold used frequency
Not Present
-W Used frequency
Not Present
-Hysteresis
0 dB
-Time to trigger
0 ms
-Reporting Cell Status (10.3..61)
-CHOICE reported cell
Report cells within active and/or monitored set on used frequency or within virtual active and/or monitored set on non-used frequency
-Maximum number of reported cells
3
-Parameters required for each non-used frequenc
- Threshold non-used frequency
-71
- W non-used frequency
1
Physical channel information elements
-DPCH compressed mode status info (10.3.6.34)
Not Present
MEASUREMENT REPORT message (step 6)
Information Element
Value/remark
Message Type (10.2.17)
Integrity check info
Not Present
Measurement identity
1
Measured Results (10.3.7.44)
-CHOICE Measurement
Inter-frequency Measured results list
-Inter-frequency measured results
1
-Frequency info
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2
-UTRA carrier RSSI
Not Present
-Inter-frequency cell measured results
1
-Cell measured results (10.3.7.3)
-Cell identity
Not Present
-SFN-SFN observed time difference
Not Present
-Cell synchronisation info
Not Present
-CHOICE mode
TDD
-Cell parameters ID
Set to cell parameters ID of Cell 2
-Proposed TGSN
Not Present
-Primary CCPCH RSCP
Checked that this IE is present
-Pathloss
Not Present
-Timeslot list
Not Present
Measured results on RACH
Not Present
Additional measured results
Not Present
Event results (10.3.7.7)
-CHOICE event result
Inter-frequency measurement event results
-Inter-frequency event identity
2C
-Inter-frequency cells
1
-Frequency Info
-CHOICE mode
TDD
-UARFCN(Nt)
Same frequency as channel 2
-Non frequency related measurement event results
-CHOICE mode
TDD
-Primary CCPCH Info
-CHOICE mode
TDD
-CHOICE TDD Option
1.28 Mcps TDD
-TSTD indicator
TRUE
-Cell Parameters ID
Set to cell parameters ID of Cell 2
-SCTD Indicator
FALSE |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.