hash stringlengths 32 32 | doc_id stringlengths 5 12 | section stringlengths 5 1.47k | content stringlengths 0 6.67M |
|---|---|---|---|
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.1.5.1 3,84 Mcps TDD option | 1) In step d), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 2.5 s.
3) In step g), the UE shall respond on cell 1 within 2.5 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than [FFS]% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.1.5.2 1,28 Mcps TDD option | 1) In step d), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 1.6 s.
3) In step g), the UE shall respond on cell 1 within 1.6 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.1.5.3 7,68 Mcps TDD option | 1) In step d), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 2.5 s.
3) In step g), the UE shall respond on cell 1 within 2.5 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than 90% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. 8.3.4.2 Scenario 2: TDD/TDD cell re-selection multi carrier case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2 Scenario 2: TDD/TDD cell re-selection multi carrier case | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.1.1 3,84 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the CELL UPDATE message with cause value "cell reselection" in the new cell.
The requirements and this test apply to the 3,84 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.1.2 1,28 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send SYNCH-UL sequence in the UpPTS for sending the CELL UPDATE with cause value "cell reselection".
The requirements and this test apply to the 1,28 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.1.3 7,68 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the CELL UPDATE message with cause value "cell reselection" in the new cell.
The requirements and this test apply to the 7,68 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.2.1 3,84 Mcps TDD option | The cell re-selection delay shall be less than 3 s. The rate of correct cell re-selections observed during repeated tests shall be at least 90%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.4.2 and A.5.4.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.2.2 1,28 Mcps TDD option | The cell re-selection delay shall be less than 2 s. The rate of correct cell re-selections observed during repeated tests shall be at least 90%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.4.3 and A.5.4.2.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.2.3 7,68 Mcps TDD option | The cell re-selection delay shall be less than 3 s. The rate of correct cell re-selections observed during repeated tests shall be at least 90%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.4.4 and A.5.4.3.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.3 Test purpose | This test verifies that the UE meets the requirement for the cell re-selection delay in CELL_FACH for the multi carrier case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4.1 3,84 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4.1.1 Initial conditions | This scenario contains 6 cells and 2 carrier frequencies. The test parameters are given in Tables 8.3.4.2.1.1, 8.3.4.2.1.2, 8.3.4.2.1.3, and 8.3.4.2.1.4.
Table 8.3.4.2.1.1: General test parameters for Cell Re-selection in CELL_FACH
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
-
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
T1
s
15
T2
s
15
Table 8.3.4.2.1.2: Physical channel parameters for S-CCPCH.
Parameter
Unit
Level
Channel bit rate
Kbps
24,4
Channel symbol rate
Ksps
12,2
Slot Format #
-
0
Frame allocation
-
Continuous frame allocation
Midamble allocation
-
Default Midamble
Table 8.3.4.2.1.3: Transport channel parameters for S-CCPCH
Parameter
FACH
Transport Channel Number
1
Transport Block Size
240
Transport Block Set Size
240
Transmission Time Interval
20 ms
Type of Error Protection
Convolutional Coding
Coding Rate
½
Rate Matching attribute
256
Size of CRC
16
Table 8.3.4.2.1.4: Cell specific test parameters for Cell Re-selection in CELL_FACH
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
10
10
10
10
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
dB
9
3
9
3
3
9
3
9
-1
-1
-1
-1
PCCPCH RSCP
dBm
-64
-70
-70
-64
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1,C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
Inter-frequency TDD measurement indicator
TRUE
TRUE
TRUE
dBm/3,84 MHz
-70
Propagation Condition
AWGN
Cell 4
Cell 5
Cell 6
Timeslot
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
15
15
15
15
20
20
20
20
25
25
25
25
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
Inter-frequency TDD measurement indicator
TRUE
TRUE
TRUE
dBm/3,84 MHz
-70
Propagation Condition
AWGN
NOTE: S-CCPCH shall not be located in TS0. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4.1.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters.
b) The UE is switched on.
c) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclauses 7.3.3 and 7.4.2 to place the UE in CELL_FACH. If the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s and if no response is received the UE shall be switched off and the procedure returns to step 1. Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for CELL UPDATE message with cause value "cell reselection" from the UE.
f) After another 15 s, the parameters are changed as described for T1. If the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s and if no response is received the UE shall be switched off and the procedure returns to step 1. Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues.
g) The SS waits for CELL UPDATE message with cause value "cell reselection" from the UE.
h) Repeat steps d) to g) [TBD] times. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4.2 1,28 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4.2.1 Initial conditions | This scenario contains 6 cells and 2 carrier frequencies. The test parameters are given in Tables 8.3.4.2.4.2.1, 8.3.4.2.4.2.2, 8.3.4.2.4.2.3, and 8.3.4.2.4.2.4.
Table 8.3.4.2.4.2.1: General test parameters for 1,28Mcps Cell Re-selection in CELL_FACH
Parameter
Unit
Value
Comment
initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
DBm
21
The value shall be used for all cells in the test.
Qrxlevmin
DBm
-103
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
S
1,28
The value shall be used for all cells in the test.
T1
S
15(initial), 15 (repetition)
T2
S
15
Table 8.3.4.2.4.2.2Physical channel parameters for S-CCPCH.
Parameter
Unit
Level
Channel bit rate
kbps
35.2
Channel symbol rate
ksps
17.6
Slot Format #
-
0; 2
Frame allocation
-
Continuous frame allocation
Midamble allocation
-
Common Midamble
Table 8.3.4.2.4.2.3 Transport channel parameters for S-CCPCH
Parameter
FACH
Transport Channel Number
1
Transport Block Size
240
Transport Block Set Size
240
Transmission Time Interval
20 ms
Type of Error Protection
Convolution Coding
Coding Rate
½
Rate Matching attribute
256
Size of CRC
16
Table 8.3.4.2.4.2.4: Cell specific test parameters for 1,28Mcps Cell re-selection in CELL_FACH state
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
10
4
10
4
4
10
4
10
-1
-1
-1
-1
PCCPCH RSCP
dBm
-63
-69
-69
-63
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1,C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2:C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3:C6:0
Qhyst1s
dBm
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
FACH measurement occasion cycle length
4
4
4
Inter-frequency TDD measurement indicator
TRUE
TRUE
TRUE
Inter-frequency FDD measurement indicator
FALSE
FALSE
FALSE
Cell 4
Cell 5
Cell 6
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0C4, C5:0; C4:C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5:C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6:C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
FACH measurement occasion cycle length
4
4
4
Inter-frequency TDD measurement indicator
TRUE
TRUE
TRUE
Inter-frequency FDD measurement indicator
FALSE
FALSE
FALSE
dBm/ 1,28 MHz
-70
Propagation Condition
AWGN
NOTE: S-CCPCH is located in an other downlink TS than TS0. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4.2.2 Procedure | The SS activates cell 1-2 with T1 defined parameters;
a) The UE switched on.
b) A RRC connection is set up according the generic set-up procedure specified in TS 34.108[3] clause 7.3.3 and 7.4.2 to place UE in CELL_FACH state;
c) After 15s the parameters changed to those defined for T2;
d) If the UE responds on cell 2 for the CHANNEL REQUEST within 7.5s, the success is recorded;
e) If the UE doesn’t respond on cell 2 for theCHANNEL REQUEST within 7.5s, a failure is recorded. The SS shall then wait for a total of 10s from the beginning of T2 and if no response is received, the UE shall be switched off and the procedure returns to step a);
f) After 15s from the beginning of T2, the UE shall be switched off;
Repeat step d) to g) until the confidence level according to annex F.6.2 is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4.3 7,68 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4.3.1 Initial conditions | This scenario contains 6 cells and 2 carrier frequencies. The test parameters are given in Tables 8.3.4.2.4.3.1, 8.3.4.2.4.3.2, 8.3.4.2.4.3.3, and 8.3.4.2.4.3.4.
Table 8.3.4.2.4.3.1: General test parameters for Cell Re-selection in CELL_FACH
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
-
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
T1
s
15 (initial),
5 (repetition)
T2
s
5
Table 8.3.4.2.4.3.2: Physical channel parameters for S-CCPCH.
Parameter
Unit
Level
Channel bit rate
Kbps
24,4
Channel symbol rate
Ksps
12,2
Slot Format #
-
0
Frame allocation
-
Continuous frame allocation
Midamble allocation
-
Default Midamble
Table 8.3.4.2.4.3.3: Transport channel parameters for S-CCPCH
Parameter
FACH
Transport Channel Number
1
Transport Block Size
240
Transport Block Set Size
240
Transmission Time Interval
20 ms
Type of Error Protection
Convolutional Coding
Coding Rate
½
Rate Matching attribute
256
Size of CRC
16
Table 8.3.4.2.4.3.4: Cell specific test parameters for Cell Re-selection in CELL_FACH
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
10
10
10
10
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
9
3
9
3
3
9
3
9
-1
-1
-1
-1
PCCPCH RSCP
dBm
-64
-70
-70
-64
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1,C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
Inter-frequency TDD measurement indicator
TRUE
TRUE
TRUE
dBm/ 7,68 MHz
-70
Propagation Condition
AWGN
Cell 4
Cell 5
Cell 6
Timeslot
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
15
15
15
15
20
20
20
20
25
25
25
25
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
Inter-frequency TDD measurement indicator
TRUE
TRUE
TRUE
dBm/ 7,68 MHz
-70
Propagation Condition
AWGN
NOTE: S-CCPCH shall not be located in TS0. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.4.3.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters.
b) The UE is switched on.
c) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclauses 7.3.3 and 7.4.2 to place the UE in CELL_FACH. If the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s and if no response is received the UE shall be switched off and the procedure returns to step 1. Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for CELL UPDATE message with cause value "cell reselection" from the UE.
f) After another 15 s, the parameters are changed as described for T1. If the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s and if no response is received the UE shall be switched off and the procedure returns to step 1. Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues.
g) The SS waits for CELL UPDATE message with cause value "cell reselection" from the UE.
h) Repeat steps d) to g) until the confidence level according to annex F.6.2 is achieved. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.5.1 3,84 Mcps TDD option | 1) In step d), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 3 s.
3) In step g), the UE shall respond on cell 2 within 3 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than [FFS]% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.5.2 1,28 Mcps TDD option | 1) In step d), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 2 s.
3) In step g), the UE shall respond on cell 2 within 2 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.2.5.3 7,68 Mcps TDD option | 1) In step d), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 3 s.
3) In step g), the UE shall respond on cell 2 within 3 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than 90% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3 Scenario 3: TDD/GSM cell re-selection | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.1.1 3,84 Mcps TDD option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.1.2 1,28 Mcps TDD option | The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send CHANNEL REQUEST message to perform a Location update to the new cell.
This test is for the case where the UE camps on a 1,28 Mcps TDD cell and reselects to a GSM cell.
The requirements and this test apply to UEs supporting both 1,28 Mcps TDD and GSM. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.1.3 7,68 Mcps TDD option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.2.1 3,84 Mcps TDD option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.2.2 1,28 Mcps TDD option | The cell re-selection delay shall be less than 5530ms + TBCCH,
NOTE: The cell re-selection delay can be expressed as:
where
: The maximum time allowed to read BCCH data from GSM cell, 1.9s.
: The additional delay caused by the random access procedure, 10ms.
Specified in TS 25.123, here it is 5000ms
: 480ms
This gives a total of 7430ms, thus allow 7.5s. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.2.3 7,68 Mcps TDD option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.3 Test purpose | This test verifies that the UE meets the minimum requirement for the inter-RAT cell re-selection delay in CELL_FACH state. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.4.1 3,84 Mcps TDD option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.4.2 1,28 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.4.2.1 Initial conditions | This scenario implies the presence of one 1.28 Mcps TDD serving cell, and one GSM cell to be re-selected. Test parameters are given in Tables 8.3.4.3.4.1, 8.3.4.3.4.2, 8.3.4.3.4.3, 8.3.4.3.4.4, 8.3.4.3.4.5.
The ranking of the cells shall be made according to the cell reselection criteria specified in TS25.304. Cell 1 and cell 2 shall belong to different location areas.
Table 8.3.4.3.4.1: General test parameters for 1,28 Mcps Cell Re-selection in CELL_FACH
Parameter
Unit
Value
Comment
initial condition
Active cell
Cell1
Neighbour cells
Cell2
final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-103
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
T1
s
15
T2
s
15
Table 8.3.4.3.4.2: Physical channel parameters for S-CCPCH
Parameter
Unit
Level
Channel bit rate
kbps
35.2
Channel symbol rate
ksps
17.6
Slot Format #
-
0; 2
Frame allocation
-
Continuous frame allocation
Midamble allocation
-
Common Midamble
Table 8.3.4.3.4.3: Transport channel parameters for FACH
Parameter
FACH
Transport Channel Number
1
Transport Block Size
240
Transport Block Set Size
240
Transmission Time Interval
20 ms
Type of Error Protection
Convolution Coding
Coding Rate
½
Rate Matching attribute
256
Size of CRC
16
Table 8.3.4.3.4.4: Cell specific test parameters for 1,28 Mcps Cell(Cell 1) Re-selection in CELL_FACH
Parameter
Unit
Cell 1 (UTRA)
Timeslot Number
0
DwPTS
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
DwPCH_Ec/Ior
dB
0
0
OCNS_Ec/Ior
dB
-3
-3
dB
6
6
6
6
dBm/1,28 MHz
-80
PCCPCH RSCP
dBm
-77
Propagation Condition
AWGN
AWGN
Treselection
s
0
SsearchRAT
dB
Not sent
Qrxlevmin
dBm
-103
Qoffset1s,n
dB
C1, C2: 0
Qhyst1s
dB
0
Table 8.3.4.3.4.5: Cell specific test parameters for Cell 2(GSM) re-selection in CELL_FACH state
Parameter
Unit
Cell 2 (GSM)
T1
T2
Absolute RF Channel Number
ARFCN 1
RXLEV
dBm
-90
-70
RXLEV_ACCESS_MIN
dBm
-103
MS_TXPWR_MAX_CCH
dBm
33
Qsearch_I
-
always |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.4.3 7,68 Mcps TDD option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.5.1 3,84 Mcps TDD option | Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.5.2 1,28 Mcps TDD option | In step d), the UE shall respond on cell 2 within 7.5 s.
For the test to pass, the total number of fulfilled test requirement shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.4.3.5.3 7,68 Mcps TDD option | Void
8.3.4A Cell Re-selection in Enhanced CELL_FACH
8.3.4A.1 Scenario 1: Cell Re-selection to Intra-Frequency TDD cell
8.3.4A.1.1 Definition and applicability
8.3.4A.1.1.1 3,84 Mcps TDD option
Void
8.3.4A.1.1.2 1,28 Mcps TDD option
The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send SYNCH-UL sequence in the UpPTS for sending the CELL UPDATE with cause value "cell reselection".
The requirements and this test apply to the 1,28 Mcps TDD UE of release 8 and later supporting Enhanced CELL_FACH.
8.3.4A.1.1.3 7,68 Mcps TDD option
Void
8.3.4A.1.2 Minimum requirement
8.3.4A.1.2.1 3,84 Mcps TDD option
Void
8.3.4A.1.2.2 1,28 Mcps TDD option
The cell re-selection delay shall be less than 1.6s.
The rate of correct cell re-selections observed during repeated tests shall be at least 90%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.4.3 and A.5.4A.2.1.
8.3.4A.1.2.3 7,68 Mcps TDD option
Void
8.3.4A.1.3 Test purpose
This test verifies that the UE meets the minimum requirement for the cell re-selection delay to intra-frequency TDD cell in Enhanced CELL_FACH.
8.3.4A.1.4 Method of test
8.3.4A.1.4.1 3,84 Mcps TDD option
Void
8.3.4A.1.4.2 1,28 Mcps TDD option
8.3.4A.1.4.2.1 Initial conditions
This scenario contains 6 cells operating on the same carrier frequency. The test parameters are given in Tables 8.3.4A.1.4.2.1 and 8.3.4A.1.4.2.2.
Table 8.3.4A.1.4.2.1: General test parameters for 1,28 Mcps Cell Re-selection to intra-frequency TDD cell in Enhanced CELL_FACH
Parameter
Unit
Value
Comment
initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-103
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
T1
s
15 (initial), 5 (repetition)
T2
s
5
Table 8.3.4A.1.4.2.2: Cell specific test parameters for 1,28 Mcps Cell Re-selection to intra-frequency TDD cell in Enhanced CELL_FACH
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
10
7
10
7
7
10
7
9
-1
-1
-1
-1
PCCPCH RSCP
dBm
-63
-66
-66
-63
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1,C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
dBm/1,28 MHz
-70
Propagation Condition
AWGN
NOTE: S-CCPCH is located in an other downlink TS than TS0..
8.3.4A.1.4.2.2 Procedure
a) The SS activates cell 1-6 with T1 defined parameters.
b) The UE is switched on.
c) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclause s 7.3.5 to place the UE in CELL_FACH.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for SYNCH-UL sequence in the UpPTS for sending CELL UPDATE message with cause value "cell reselection" from the UE. If the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s and if no response is received the UE shall be switched off and the procedure returns to step 1. Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues.
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for SYNCH-UL sequence in the UpPTS for sending CELL UPDATE message with cause value "cell reselection" from the UE. If the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15 s and if no response is received the UE shall be switched off and the procedure returns to step 1. Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues
h) Repeat steps until the confidence level according to annex F.6.2 is achieved.
8.3.4A.1.4.3 7,68 Mcps TDD option
Void
8.3.4A.1.5 Test Requirements
8.3.4A.1.5.1 3,84 Mcps TDD option
Void
8.3.4A.1.5.2 1,28 Mcps TDD option
1) In step d), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 2 within 1.6 s.
3) In step g), the UE shall respond on cell 1 within 1.6 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.4A.1.5.3 7,68 Mcps TDD option
Void
8.3.4A.1 Scenario 2: Cell Re-selection to Inter-Frequency TDD cell
8.3.4A.2.1 Definition and applicability
8.3.4A.2.1.1 3,84 Mcps TDD option
Void
8.3.4A.2.1.2 1,28 Mcps TDD option
The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send SYNCH-UL sequence in the UpPTS for sending the CELL UPDATE with cause value "cell reselection".
The requirements and this test apply to the 1,28 Mcps TDD UE.
8.3.4A.2.1.3 7,68 Mcps TDD option
Void
8.3.4A.2.2 Minimum requirement
8.3.4A.2.2.1 3,84 Mcps TDD option
Void
8.3.4A.2.2.2 1,28 Mcps TDD option
The cell re-selection delay shall be less than 2 s. The rate of correct cell re-selections observed during repeated tests shall be at least 90%.
The normative reference for this requirement is TS 25.123 [2] clauses 5.4.3 and A.5.4A.2.2.
8.3.4A.2.2.3 7,68 Mcps TDD option
Void
8.3.4A.2.3 Test purpose
This test verifies that the UE meets the requirement for the cell re-selection delay to inter-frequency TDD cell in Enhanced CELL_FACH.
8.3.4A.2.4 Method of test
8.3.4A.2.4.1 3,84 Mcps TDD option
Void
8.3.4A.2.4.2 1,28 Mcps TDD option
8.3.4A.2.4.2.1 Initial conditions
This scenario contains 6 cells and 2 carrier frequencies. The test parameters are given in Tables 8.3.4A.2.4.2.1 and 8.3.4A.2.4.2.2.
Table 8.3.4A.2.4.2.1: General test parameters for 1,28Mcps Cell Re-selection to inter-freqency TDD cell in Enhanced CELL_FACH
Parameter
Unit
Value
Comment
initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
DBm
21
The value shall be used for all cells in the test.
Qrxlevmin
DBm
-103
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
S
1,28
The value shall be used for all cells in the test.
T1
S
15(initial), 5 (repetition)
T2
S
5
Table 8.3.4A.2.4.2.2: Cell specific test parameters for 1,28Mcps Cell re-selection to inter-freqency TDD cell in Enhanced CELL_FACH state
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
10
4
10
4
4
10
4
10
-1
-1
-1
-1
PCCPCH RSCP
dBm
-63
-69
-69
-63
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1,C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2:C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3:C6:0
Qhyst1s
dBm
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
FACH measurement occasion cycle length
4
4
4
Inter-frequency TDD measurement indicator
TRUE
TRUE
TRUE
Inter-frequency FDD measurement indicator
FALSE
FALSE
FALSE
Cell 4
Cell 5
Cell 6
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0C4, C5:0; C4:C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5:C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6:C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
FACH measurement occasion info
not sent
not sent
not sent
FACH measurement occasion cycle length
4
4
4
Inter-frequency TDD measurement indicator
TRUE
TRUE
TRUE
Inter-frequency FDD measurement indicator
FALSE
FALSE
FALSE
dBm/ 1,28 MHz
-70
Propagation Condition
AWGN
NOTE: S-CCPCH is located in an other downlink TS than TS0.
8.3.4A.2.4.2.2 Procedure
a) The SS activates cell 1-6 with T1 defined parameters.
b) The UE is switched on.
c) A call is set up according to the generic set-up procedure specified in TS 34.108 [3] subclauses 7.3.5 to place the UE in CELL_FACH.
d) After 15 s, the parameters are changed as described for T2.
e) The SS waits for SYNCH-UL sequence in the UpPTS for sending CELL UPDATE message with cause value "cell reselection" from the UE. If the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s and if no response is received the UE shall be switched off and the procedure returns to step 1. Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues
f) After another 15 s, the parameters are changed as described for T1.
g) The SS waits for SYNCH-UL sequence in the UpPTS for sending CELL UPDATE message with cause value "cell reselection" from the UE. If the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s and if no response is received the UE shall be switched off and the procedure returns to step 1. Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues
h) Repeat steps d) to g)until the confidence level according to annex F.6.2 is achieved.
8.3.4A.2.4.3 7,68 Mcps TDD option
Void
8.3.4A.2.5 Test Requirements
8.3.4A.2.5.1 3,84 Mcps TDD option
Void
8.3.4A.2.5.2 1,28 Mcps TDD option
1) In step d), after the UE has responded on cell 1, it shall not respond on any other cell (cell selection).
2) In step e), the UE shall respond on cell 1 within 1.9 s.
3) In step g), the UE shall respond on cell 2 within 1.9 s.
For the test to pass, the total number of fulfilled test requirements 2) and 3) shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4.
8.3.4A.2.5.3 7,68 Mcps TDD option
Void |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5 Cell Re-selection in CELL_PCH | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1 Scenario 1: TDD/TDD cell re-selection single carrier case | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.1.1 3,84 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the CELL UPDATE message with cause value "cell reselection" in the new cell.
The requirements and this test apply to the 3,84 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.1.2 1,28 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send SYNCH-UL sequence in the UpPTS for sending the CELL UPDATE with cause value "cell reselection".
The requirements and this test apply to the 1,28 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.1.3 7,68 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the CELL UPDATE message with cause value "cell reselection" in the new cell.
The requirements and this test apply to the 7,68 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.2.1 3,84 Mcps TDD option | The cell re-selection delay shall be less than 8 s.
NOTE:
The cell re-selection delay can be expressed as: TevaluateTDD + TSI, where:
TevaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to TS 25.123 [2] table 4.1 in clause 4.2.2.7.
TSI Maximum repetition period of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 5.5 and A.5.5.1. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.2.2 1,28 Mcps TDD option | The cell re-selection delay shall be less than 8 s.
NOTE:
The cell re-selection delay can be expressed as: TevaluateNTDD + TSI, where:
TevaluateNTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to TS 25.123 [2] table 4.1a in clause 4.2.2.
TSI Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell (ms). 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allowing 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 5.5.2.2 and A.5.5.1. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.2.3 7,68 Mcps TDD option | The cell re-selection delay shall be less than 8 s.
NOTE:
The cell re-selection delay can be expressed as: TevaluateTDD + TSI, where:
TevaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to TS 25.123 [2] table 4.1B in clause 4.2.2.7.3.
TSI Maximum repetition period of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 5.5.2.3 and A.5.5.1. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.3 Test purpose | This test verifies that the UE meets the minimum requirement for the cell re-selection delay in CELL_PCH for the single carrier case |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4.1 3,84 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4.1.1 Initial conditions | This scenario contains 6 cells operating on the same carrier frequency. The test parameters are given in Tables 8.3.5.1.1.1, and 8.3.5.1.1.2.
Table 8.3.5.1.1.1: General test parameters for Cell Re-selection single carrier multi-cell case
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
15
T2
s
15
Table 8.3.5.1.1.2: Cell re-selection single carrier multi-cell case
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
10
10
10
10
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
dB
9
7
9
7
7
9
7
9
-1
-1
-1
-1
PCCPCH RSCP
dBm
-64
-66
-66
-64
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1, C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
15
15
15
15
20
20
20
20
25
25
25
25
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
dBm/3,84 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4.1.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters.
b) The UE is switched on.
c) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.4.2.7.1 to place the UE in the CELL_PCH state on Cell 1 and then the SS waits for this process to complete.
d) After 15 s from the completion of step c) or the beginning of T1, the parameters are changed as described for T2.
e) If the UE responds on Cell 2 with a PRACH (CELL UPDATE message cause "cell reselection") within 8s, then a success is recorded, the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure moves to step g).
f) Since the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T2 and if no response is received, the UE shall be switched off and the procedure returns to step a). Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step g).
g) After a total of 15 s from the beginning of T2, the parameters are changed as described for T1.
h) If the UE responds on Cell 1 with a PRACH (CELL UPDATE message cause "cell reselection") within 8s, then a success is recorded and the procedure moves to step j).
i) Since the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T1 and if no response is received the UE shall be switched off and the procedure returns to step a). Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step j).
j) Repeat steps d) to i) [TBD] times.
NOTE: The time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell. Since the maximum repetition period of the relevant system info blocks that needs to be received by the UE to camp on a cell is 1280ms and the maximum RRC procedure delay for reception system information block is 100ms, 1380 ms is assumed in this test case. Therefore this gives a total of 7.78s(Minimum requirement + 100ms), allow 8s in the test case.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3], with the following exceptions:
RADIO BEARER SETUP (Step 3)
Information Element
Value/remark
RRC State Indicator
CELL PCH
UTRAN DRX cycle length coefficient
7 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4.2 1,28 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4.2.1 Initial conditions | This scenario contains 6 cells operating on the same carrier frequency. The test parameters are given in Tables 8.3.5.1.4.2.1 and 8.3.5.1.4.2.2.
Table 8.3.5.1.4.2.1: General test parameters for 1,28 Mcps Cell Re-selection single carrier multi-cell case
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3, Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-103
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑– Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
15
T2
s
15
Table 8.3.5.1.4.2.2: 1,28Mcps Cell re-selection single carrier multi-cell case
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
10
7
10
7
7
10
7
10
-1
-1
-1
-1
PCCPCH RSCP
dBm
-63
-66
-66
-63
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1,C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
dBm/1,28 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4.2.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters.
b) The UE is switched on.
c) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.4.2.7.1 to place the UE in the CELL_PCH state on Cell 1 and then the SS waits for this process to complete.
d) After 15 s from the completion of step c) or the beginning of T1, the parameters are changed as described for T2.
e) If the UE responds on Cell 2 with a SYNCH-UL sequence in the UpPTS for sending CELL UPDATE message cause "cell reselection" within 8s, then a success is recorded.After receiving the CELL UPDATE message cause “cell reselection”,the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure moves to step g).
f) If the UE has failed to respond with a SYNCH-UL sequence in the UpPTS within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T2 and if no response is received, the UE shall be switched off and the procedure returns to step a). Otherwise after receiving the CELL UPDATE message cause “cell reselection”,the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step g).
g) After a total of 15 s from the beginning of T2, the parameters are changed as described for T1.
h) If the UE responds on Cell 1 with a SYNCH-UL sequence in the UpPTS for sending CELL UPDATE message cause "cell reselection" within 8s, then a success is recorded and the procedure moves to step j).
i) If the UE has failed to respond with SYNCH-UL sequence in the UpPTS within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T1 and if no response is received the UE shall be switched off and the procedure returns to step a). Otherwise after receiving the CELL UPDATE message cause “cell reselection”,the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step j).
j) After another 15 s, the UE shall be switched off.
k) Repeat steps a) toj) until the confidence level according to annex F.6.2 is achieved
NOTE: The time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell. Since the maximum repetition period of the relevant system info blocks that needs to be received by the UE to camp on a cell is 1280ms and the maximum RRC procedure delay for reception system information block is 100ms, 1380 ms is assumed in this test case. Therefore this gives a total of 7.78s(Minimum requirement + 100ms), so allow 8s in the test case.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3], with the following exceptions:
RADIO BEARER SETUP (Step 3)
Information Element
Value/remark
RRC State Indicator
CELL PCH
UTRAN DRX cycle length coefficient
7 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4.3 7,68 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4.3.1 Initial conditions | This scenario contains 6 cells operating on the same carrier frequency. The test parameters are given in Tables 8.3.5.1.4.3.1, and 8.3.5.1.4.3.2.
Table 8.3.5.1.4.3.1: General test parameters for Cell Re-selection single carrier multi-cell case
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1.28
The value shall be used for all cells in the test.
DRX cycle length
s
1.28
The value shall be used for all cells in the test.
T1
s
15
T2
s
15
Table 8.3.5.1.4.3.2: Cell re-selection single carrier multi-cell case
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
10
10
10
10
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
9
7
9
7
7
9
7
9
-1
-1
-1
-1
PCCPCH RSCP
dBm
-64
-66
-66
-64
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0
C1, C5:0; C1,C6:0
C2, C1: 0; C2, C3:0; C2,C4:0
C2, C5: 0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5: 0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 1
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
15
15
15
15
20
20
20
20
25
25
25
25
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
dBm/7,68 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.4.3.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters.
b) The UE is switched on.
c) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.4.2.7.1 to place the UE in the CELL_PCH state on Cell 1 and then the SS waits for this process to complete.
d) After 15 s from the completion of step c) or the beginning of T1, the parameters are changed as described for T2.
e) If the UE responds on Cell 2 with a PRACH (CELL UPDATE message cause "cell reselection") within 8s, then a success is recorded, the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure moves to step g).
f) Since the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T2 and if no response is received, the UE shall be switched off and the procedure returns to step a). Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step g).
g) After a total of 15 s from the beginning of T2, the parameters are changed as described for T1.
h) If the UE responds on Cell 1 with a PRACH (CELL UPDATE message cause "cell reselection") within 8s, then a success is recorded and the procedure moves to step j).
i) Since the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T1 and if no response is received the UE shall be switched off and the procedure returns to step a). Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step j).
j) Repeat steps d) to i) until the confidence level according to annex F.6.2 is achieved..
NOTE: The time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell. Since the maximum repetition period of the relevant system info blocks that needs to be received by the UE to camp on a cell is 1280ms and the maximum RRC procedure delay for reception system information block is 100ms, 1380 ms is assumed in this test case. Therefore this gives a total of 7.78s(Minimum requirement + 100ms), allow 8s in the test case.
Specific Message Contents
All messages indicated above shall use the same content as described in the default message content in clause 9 of 34.108 [3], with the following exceptions:
RADIO BEARER SETUP (Step 3)
Information Element
Value/remark
RRC State Indicator
CELL PCH
UTRAN DRX cycle length coefficient
7 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.5.1 3,84 Mcps TDD option | For the test to pass, the total number of successful attempts shall be more than 90% with a confidence level of [FFS]% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.5.2 1,28 Mcps TDD option | For the test to pass, the total number of successful attempts shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.1.5.3 7,68 Mcps TDD option | For the test to pass, the total number of successful attempts shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2 Scenario 2: TDD/TDD cell re-selection multi carrier case | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.1.1 3,84 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the CELL UPDATE message with cause value "cell reselection" in the new cell.
The requirements and this test apply to the 3,84 Mcps option TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.1.2 1,28 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send SYNCH-UL sequence in the UpPTS for sending the CELL UPDATE with cause value "cell reselection".
The requirements and this test apply to the 1,28 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.1.3 7,68 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the CELL UPDATE message with cause value "cell reselection" in the new cell.
The requirements and this test apply to the 7,68 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.2 Minimum requirement | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.2.1 3,84 Mcps TDD option | The cell re-selection delay shall be less than 8 s.
NOTE:
The cell re-selection delay can be expressed as: TevaluateTDD + TSI, where:
TevaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to TS 25.123 [2] table 4.1 in clause 4.2.2.7.
TSI Maximum repetition period of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 5.5 and A.5.5.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.2.2 1,28 Mcps TDD option | The cell re-selection delay shall be less than 8 s.
NOTE:
The cell re-selection delay can be expressed as: TevaluateNTDD + TSI, where:
TevaluateNTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to TS 25.123 [2] table 4.1a in clause 4.2.2.
TSI Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell (ms). 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allowing 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 5.5.2 and A.5.5.2.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.2.3 7,68 Mcps TDD option | The cell re-selection delay shall be less than 8 s.
NOTE:
The cell re-selection delay can be expressed as: TevaluateTDD + TSI, where:
TevaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a Tevaluate TDD of 6.4s according to TS 25.123 [2] table 4.1B in clause 4.2.2.7.3.
TSI Maximum repetition period of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.
This gives a total of 7.68 s, allow 8s in the test case.
The normative reference for this requirement is TS 25.123 [2] clauses 5.5.2 and A.5.5.2. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.3 Test purpose | This test verifies that the UE meets the requirement for the cell re-selection delay in CELL_PCH for the multi carrier case. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.4 Method of test | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.4.1 3,84 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.4.1.1 Initial conditions | This scenario contains 6 cells and 2 carrier frequencies. The test parameters are given in Tables 8.3.5.2.1.1 and 8.3.5.2.1.2.
Table 8.3.5.2.1.1: General test parameters for Cell Re-selection in Multi carrier case
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
30
T2
s
15
Table 8.3.5.2.1.2: Cell re-selection multi carrier multi cell case
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
10
10
10
10
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
dB
6
0
6
0
0
6
0
6
-3
-3
-3
-3
PCCPCH RSCP
dBm
-67
-73
-73
-67
-76
-76
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0C1, C5:0; C1, C6:0
C2, C1: 0; C2, C3:0; C2,C4:0C2, C5:0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5:0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
15
15
15
15
20
20
20
20
25
25
25
25
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
-4,28
dB
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
PCCPCH RSCP
dBm
-76
-76
-76
-76
-76
-76
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0
C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
dBm/3,84 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.4.1.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters.
b) The UE is switched on.
c) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.4.2.7.1 to place the UE in the CELL_PCH state on Cell 1 and then the SS waits for this process to complete.
d) After 15 s from the completion of step c) or the beginning of T1, the parameters are changed as described for T2.
e) If the UE responds on Cell 2 with a PRACH (CELL UPDATE message cause "cell reselection") within 8s, then a success is recorded, the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure moves to step g).
f) Since the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T2 and if no response is received, the UE shall be switched off and the procedure returns to step a). Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step g).
g) After a total of 15 s from the beginning of T2, the parameters are changed as described for T1.
h) If the UE responds on Cell 1 with a PRACH (CELL UPDATE message cause "cell reselection") within 8s, then a success is recorded and the procedure moves to step j).
i) Since the UE has failed to respond with the correct message within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T1 and if no response is received the UE shall be switched off and the procedure returns to step a). Otherwise the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step j).
j) Repeat steps d) to i) until the confidence level according to annex F.6.2 is achieved..
NOTE 1: T1 is initially 30 s to allow enough time for the UE to search for cells as it has no prior knowledge of these.
NOTE 2: The time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell. Since the maximum repetition period of the relevant system info blocks that needs to be received by the UE to camp on a cell is 1280ms and the maximum RRC procedure delay for reception system information block is 100ms, 1380 ms is assumed in this test case. Therefore this gives a total of 7.78s(Minimum requirement + 100ms), allow 8s in the test case.
RADIO BEARER SETUP (Step 3)
Information Element
Value/remark
RRC State Indicator
CELL PCH
UTRAN DRX cycle length coefficient
7 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.4.2 1,28 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.4.2.1 Initial conditions | This scenario contains 6 cells and 2 carrier frequencies. The test parameters are given in Tables 8.3.5.2.4.2.1 and 8.3.5.2.4.2.2.
Table 8.3.5.2.4.2.1: General test parameters for 1,28Mcps Cell Re-selection in Multi carrier case
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3, Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-103
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1,28
The value shall be used for all cells in the test.
DRX cycle length
s
1,28
The value shall be used for all cells in the test.
T1
s
30
T2
s
15
Table 8.3.5.2.4.2.2: Cell re-selection 1,28 Mcps multi carrier multi cell case
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
10
4
10
4
4
10
4
10
-1
-1
-1
-1
PCCPCH RSCP
dBm
-63
-69
-69
-63
-74
-74
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1, C6:0
C2, C1: 0; C2, C3:0; C2,C4:0C2, C5:0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5:0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
DWPTS
0
DWPTS
0
DWPTS
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
DwPCH_Ec/Ior
dB
0
0
0
0
0
0
OCNS_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
dB
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
-1
PCCPCH RSCP
dBm
-74
-74
-74
-74
-74
-74
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0
C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
dBm/ 1,28 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.4.2.2 Procedure | a) The SS activates cell 1-6 with T1 defined parameters.
b) The UE is switched on.
c) A call is set up according to the test procedure specified in TS 34.108 [3] subclause 7.4.2.7.1 to place the UE in the CELL_PCH state on Cell 1 and then the SS waits for this process to complete.
d) After 15 s from the completion of step c) or the beginning of T1, the parameters are changed as described for T2.
e) If the UE responds on Cell 2 with a SYNCH-UL sequence in the UpPTS for sending CELL UPDATE message cause "cell reselection" within 8s, then a success is recorded.After receiving the CELL UPDATE message cause "cell reselection",the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure moves to step g).
f) If the UE has failed to respond with SYNCH-UL sequence in the UpPTSwithin the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T2 and if no response is received, the UE shall be switched off and the procedure returns to step a). Otherwise after receiving the CELL UPDATE message cause "cell reselection",the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step g).
g) After a total of 15 s from the beginning of T2, the parameters are changed as described for T1.
h) If the UE responds on Cell 1 with a SYNCH-UL sequence in the UpPTS for sending CELL UPDATE message cause "cell reselection" within 8s, then a success is recorded and the procedure moves to step j).
i) If the UE has failed to respond with SYNCH-UL sequence in the UpPTS within the allowed time, a failure is recorded. The SS shall then wait for a total of 15s from the beginning of T1 and if no response is received the UE shall be switched off and the procedure returns to step a). Otherwise after receiving the CELL UPDATE message cause "cell reselection",the SS shall transmit a CELL UPDATE CONFIRM message and then the procedure continues with step j).
j) After another 15 s, the UE shall be switched off.
k) Repeat steps a) toj) until the confidence level according to annex F.6.2 is achieved
NOTE 1: T1 should initially be 30 s to allow enough time for the UE to search for cells as it has no prior knowledge of these.
NOTE 2: The time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell. Since the maximum repetition period of the relevant system info blocks that needs to be received by the UE to camp on a cell is 1280ms and the maximum RRC procedure delay for reception system information block is 100ms, 1380 ms is assumed in this test case. Therefore this gives a total of 7.78s(Minimum requirement + 100ms), allow 8s in the test case.
RADIO BEARER SETUP (Step 3)
Information Element
Value/remark
RRC State Indicator
CELL PCH
UTRAN DRX cycle length coefficient
7 |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.4.3 7,68 Mcps TDD option | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.4.3.1 Initial conditions | This scenario contains 6 cells and 2 carrier frequencies. The test parameters are given in Tables 8.3.5.2.4.3.1 and 8.3.5.2.4.3.2.
Table 8.3.5.2.4.3.1: General test parameters for Cell Re-selection in Multi carrier case
Parameter
Unit
Value
Comment
Initial condition
Active cell
Cell1
Neighbour cells
Cell2, Cell3,Cell4, Cell5, Cell6
Final condition
Active cell
Cell2
HCS
Not used
UE_TXPWR_MAX_RACH
dBm
21
The value shall be used for all cells in the test.
Qrxlevmin
dBm
-102
The value shall be used for all cells in the test.
Access Service Class (ASC#0)
‑ Persistence value
1
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
TSI
s
1.28
The value shall be used for all cells in the test.
DRX cycle length
s
1.28
The value shall be used for all cells in the test.
T1
s
30
T2
s
15
Table 8.3.5.2.4.3.2: Cell re-selection multi carrier multi cell case
Parameter
Unit
Cell 1
Cell 2
Cell 3
Timeslot Number
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 1
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
0
0
0
0
5
5
5
5
10
10
10
10
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
6
0
6
0
0
6
0
6
-3
-3
-3
-3
PCCPCH RSCP
dBm
-67
-73
-73
-67
-76
-76
Qoffset1s,n
dB
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1, C6:0
C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5:0; C2, C6:0
C3, C1: 0; C3, C2:0; C3,C4:0
C3, C5:0; C3, C6:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
Cell 4
Cell 5
Cell 6
Timeslot
0
8
0
8
0
8
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
T1
T2
UTRA RF Channel Number
Channel 1
Channel 2
Channel 2
PCCPCH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
SCH_Ec/Ior
dB
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
-9
SCH_toffset
15
15
15
15
20
20
20
20
25
25
25
25
PICH_Ec/Ior
dB
-3
-3
-3
-3
-3
-3
OCNS_Ec/Ior
dB
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
-3,12
dB
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
-3
PCCPCH RSCP
dBm
-76
-76
-76
-76
-76
-76
Qoffset1s,n
dB
C4, C1: 0; C4, C2:0; C4,C3:0
C4, C5:0; C4, C6:0
C5, C1: 0; C5, C2:0; C5,C3:0
C5, C4:0; C5, C6:0
C6, C1: 0; C6, C2:0; C6,C3:0
C6, C4:0; C6, C5:0
Qhyst1s
dB
0
0
0
Treselection
s
0
0
0
Sintrasearch
dB
not sent
not sent
not sent
Sintersearch
dB
not sent
not sent
not sent
dBm/7,68 MHz
-70
Propagation Condition
AWGN |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.5 Test Requirements | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.5.1 3,84 Mcps TDD option | For the test to pass, the total number of successful attempts shall be more than 90% with a confidence level of [FFS]% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.5.2 1,28 Mcps TDD option | For the test to pass, the total number of successful attempts shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.5.2.5.3 7,68 Mcps TDD option | For the test to pass, the total number of successful attempts shall be more than 90% with a confidence level of 95% of the cases.
NOTE: If the above Test Requirement differs from the Minimum Requirement then the Test Tolerance applied for this test is non-zero. The Test Tolerance for this test is defined in clause F.2 and the explanation of how the Minimum Requirement has been relaxed by the Test Tolerance is given in clause F.4. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.6 Cell Re-selection in URA_PCH | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.6.1 Scenario 1: TDD/TDD cell re-selection single carrier case | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.6.1.1 Definition and applicability | |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.6.1.1.1 3,84 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the URA UPDATE message with cause value "change of URA" in the new cell.
The requirements and this test apply to the 3,84 Mcps TDD UE. |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.6.1.1.2 1,28 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the SYNCH-UL sequence in the UpPTS for sending URA UPDATE message with cause value "change of URA" in the new cell.
The requirements and this test apply to the 1,28 Mcps TDD UE. The two cells shall belong to different UTRAN Registration Areas (URAs). |
40bd05ebf1e9d686c3dc55dd3e817398 | 34.122 | 8.3.6.1.1.3 7,68 Mcps TDD option | The cell re-selection delay is defined as the time from a change of cell levels to the moment when this change causes the UE to camp on a new cell , and starts to send the URA UPDATE message with cause value "change of URA" in the new cell.
The requirements and this test apply to the 7,68 Mcps TDD UE. |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.